Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

Alpine Terminator


User Tag List

+ Reply to Thread
Page 1 of 3 123 LastLast
Results 1 to 15 of 43
Like Tree42Likes

Thread: Piece of shit fucking Redding Big Boss press!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

  1. #1
    Caretaker stug's Avatar
    Join Date
    May 2012
    Location
    Rolleston, Canterbury
    Posts
    4,850

    Piece of shit fucking Redding Big Boss press!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

    So my 15 year old Lee press broke last year. I figured an expensive Redding Big Boss press would be an improvement. It has always been quite stiff to raise and lower the ram. I figured it was new and the tolerances were quite tight.
    Tonight it completely seized up. I ended up having to get the sledgehammer out to get the ram out. Turns out there is a big gouge in the ram and inside the sleeve the ram goes through. It starts just below where the primers fall out. Looks like some old primer material has got down between the ram and sleeve and has gouged out both.
    Gave everything a good sand with some wet and dry to try ans smooth it out. Worked for a bit, but was still very stiff. Now it has seized again!!! Part way through loading up 100 9mm rounds.
    Fuckin piece of shit press!!!!!!!!!!!!!!!!!!!!!!!!!!!
    P38 and Huk like this.

  2. #2
    Caretaker
    Join Date
    Dec 2011
    Location
    Hawkes Bay
    Posts
    8,759
    Send it back under warranty


    Sent from my iPhone using Tapatalk
    Feather or Shoot likes this.
    A big fast bullet beats a little fast bullet every time

  3. #3
    Caretaker stug's Avatar
    Join Date
    May 2012
    Location
    Rolleston, Canterbury
    Posts
    4,850
    I've had too long to send it back. I took the ram out again and took the wire wheel on the dremel to it, then the wet and dry again. Better than new now. Shouldn't have happened in the first place though.

  4. #4
    Member Micky Duck's Avatar
    Join Date
    Apr 2015
    Location
    Geraldine
    Posts
    22,373
    there is something to be said for good old LEE stuff,it mightnt be the sexyist girl at the dance but it sure knows how to boogy.
    P38, madjon_, Savage1 and 4 others like this.

  5. #5
    Member
    Join Date
    Dec 2011
    Location
    NI
    Posts
    11,852
    Ouch.

    Don't work on my stock until you are in a better mood please.
    Maca49, shift14, Boaraxa and 2 others like this.

  6. #6
    Caretaker stug's Avatar
    Join Date
    May 2012
    Location
    Rolleston, Canterbury
    Posts
    4,850
    The air was rather blue for a while, heading back out there soon to finish off loading, fingers crossed.
    SlimySquirrel likes this.

  7. #7
    Member
    Join Date
    Jul 2014
    Location
    BOP
    Posts
    3,909
    Annoying when expensive gear packs a sad, but sounds as if you sorted it but it shouldn't have happened in the first place.

  8. #8
    P38
    P38 is offline
    Member P38's Avatar
    Join Date
    Dec 2011
    Location
    Hastings
    Posts
    5,692
    I feel your pain @stug

    Redding gear is usually spot on ............. But then so is my 40 year old Lee press

    Sounds like you have it sorted now.

    Cheers
    Pete
    Tim Dicko likes this.
    Arguing with an Engineer is like Wrestling a Pig in Mud.

    After awhile you realise the Pig loves it.

  9. #9
    Caretaker stug's Avatar
    Join Date
    May 2012
    Location
    Rolleston, Canterbury
    Posts
    4,850
    Yep smoothed it out and got the 9mm finished. I'll feel better on Sunday when I'm blasting a few targets!
    P38, outdoorlad and seano like this.

  10. #10
    Member viper's Avatar
    Join Date
    Feb 2015
    Location
    Rabbitvegas
    Posts
    2,592
    Piss off though, fork out for a serious bit of kit and it performs like that. You just wait for it to play up again.

  11. #11
    Member
    Join Date
    May 2015
    Location
    Rolleston
    Posts
    559
    I also broke my Lee challenger press. Got a classic cast now, but also fixed the old one - Titan reloading sell all the bits, only a few bucks to get the oldy going again. Now use it for depriming before cleaning the cases.

  12. #12
    Full of shit Ryan_Songhurst's Avatar
    Join Date
    Sep 2015
    Location
    South Island
    Posts
    10,207
    At least it didn't crack clean through the press body like my RCBS rockchucker did....

  13. #13
    MSL
    MSL is offline
    Member MSL's Avatar
    Join Date
    May 2014
    Location
    Waikato
    Posts
    6,384
    Did you grease the ram when you got it?
    Gibo likes this.

  14. #14
    Member
    Join Date
    Nov 2012
    Location
    BOP
    Posts
    20,760
    Donald will be having them made back in the USA shortly, so all will come right
    Fisherman and Tommy like this.
    Boom, cough,cough,cough

  15. #15
    Caretaker stug's Avatar
    Join Date
    May 2012
    Location
    Rolleston, Canterbury
    Posts
    4,850
    Quote Originally Posted by MSL View Post
    Did you grease the ram when you got it?
    Oiled but not greased. Have oiled it since. I don't think greasing would have stopped the gouging caused by something being caught in there.

 

 

Similar Threads

  1. Redding T7 turret press
    By ChrisF in forum Reloading and Ballistics
    Replies: 16
    Last Post: 25-06-2013, 03:22 PM
  2. How to be a fucking spaz
    By Bavarian_Hunter in forum Reloading and Ballistics
    Replies: 9
    Last Post: 10-02-2013, 02:59 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!