PaulNZ
Member

365 Likes

Page 1 of 25 123456789101112131415 ... Last

• Jump to page:

1. 
   country cuts liked post by PaulNZ On thread : Falcon ammo

   Couldn't get the powder they needed apparently; global propellant shortage. Some Falcon loads are going to be tough to find this year. A pity - it's good stuff.

   Liked On: 06-04-2024, 05:55 AM

2. 
   rockland liked post by PaulNZ On thread : Falcon ammo

   Couldn't get the powder they needed apparently; global propellant shortage. Some Falcon loads are going to be tough to find this year. A pity - it's good stuff.

   Liked On: 31-03-2024, 09:52 PM

3. 
   Micky Duck liked post by PaulNZ On thread : 124 Hammer vs Red Hind

   Are we watching the same video here? Here's the frame immediately prior to impact and I've marked the bullet (trace) location with an arrow. Sure, a bit low - but what you've written seems a hell of...

   Liked On: 27-03-2024, 01:33 PM

4. 
   ANTSMAN liked post by PaulNZ On thread : 124 Hammer vs Red Hind

   Are we watching the same video here? Here's the frame immediately prior to impact and I've marked the bullet (trace) location with an arrow. Sure, a bit low - but what you've written seems a hell of...

   Liked On: 24-03-2024, 10:27 PM

5. 
   30late liked post by PaulNZ On thread : 7mm RM in the bush?

   High impact velocity generally gives more bullet expansion, not less. I'm pretty sure most of the 'it was too close and the bullet zipped through without expanding' stories are actually code for 'I...

   Liked On: 02-03-2024, 07:58 AM

6. 
   samohtxotom liked post by PaulNZ On thread : 7mm RM in the bush?

   High impact velocity generally gives more bullet expansion, not less. I'm pretty sure most of the 'it was too close and the bullet zipped through without expanding' stories are actually code for 'I...

   Liked On: 29-02-2024, 09:33 PM

7. 
   gimp liked post by PaulNZ On thread : 7mm RM in the bush?

   High impact velocity generally gives more bullet expansion, not less. I'm pretty sure most of the 'it was too close and the bullet zipped through without expanding' stories are actually code for 'I...

   Liked On: 29-02-2024, 01:54 PM

8. 
   Micky Duck liked post by PaulNZ On thread : 7mm RM in the bush?

   High impact velocity generally gives more bullet expansion, not less. I'm pretty sure most of the 'it was too close and the bullet zipped through without expanding' stories are actually code for 'I...

   Liked On: 29-02-2024, 12:59 PM

9. 
   Quintin liked post by PaulNZ On thread : 7mm RM in the bush?

   High impact velocity generally gives more bullet expansion, not less. I'm pretty sure most of the 'it was too close and the bullet zipped through without expanding' stories are actually code for 'I...

   Liked On: 29-02-2024, 12:18 PM

10. 
    7mmsaum liked post by PaulNZ On thread : 7mm RM in the bush?

    High impact velocity generally gives more bullet expansion, not less. I'm pretty sure most of the 'it was too close and the bullet zipped through without expanding' stories are actually code for 'I...

    Liked On: 29-02-2024, 11:08 AM

11. 
    Roarless20 liked post by PaulNZ On thread : 7mm RM in the bush?

    High impact velocity generally gives more bullet expansion, not less. I'm pretty sure most of the 'it was too close and the bullet zipped through without expanding' stories are actually code for 'I...

    Liked On: 29-02-2024, 11:02 AM

12. 
    HNTMAD liked post by PaulNZ On thread : 7mm RM in the bush?

    High impact velocity generally gives more bullet expansion, not less. I'm pretty sure most of the 'it was too close and the bullet zipped through without expanding' stories are actually code for 'I...

    Liked On: 29-02-2024, 10:58 AM

13. 
    RV1 liked post by PaulNZ On thread : What did I do wrong?

    Here's one panel in progress, where I straightened each line as I went. The stock surface is not as curved as your example though. 243658 243659 I don't have a photo to hand of the panel cut...

    Liked On: 14-02-2024, 01:45 PM

14. 
    erniec liked post by PaulNZ On thread : What did I do wrong?

    Here's one panel in progress, where I straightened each line as I went. The stock surface is not as curved as your example though. 243658 243659 I don't have a photo to hand of the panel cut...

    Liked On: 13-02-2024, 08:43 PM

15. 
    Micky Duck liked post by PaulNZ On thread : What did I do wrong?

    Here's one panel in progress, where I straightened each line as I went. The stock surface is not as curved as your example though. 243658 243659 I don't have a photo to hand of the panel cut...

    Liked On: 13-02-2024, 06:49 PM

Page 1 of 25 123456789101112131415 ... Last

• Jump to page: