I just used an .30 cal collar on an OAL gauge to measure the bump. I don't bother any more.
But yeah, just adjust the die down an 1/8 of a turn until you achieve the desired result. All that you...
Type: Posts; User: R93
I just used an .30 cal collar on an OAL gauge to measure the bump. I don't bother any more.
But yeah, just adjust the die down an 1/8 of a turn until you achieve the desired result. All that you...
Pretty sure 10 thou was all I needed as well but got a bit more in case I ever needed it.
Change of brass brands etc.
Sent from my SM-G935F using Tapatalk
What ever gives you a bump with the feeler gauge.
I got 15 thou off mine iirc.
Adjusted until I got the bump I wanted and locked her solid. Works a treat now😆
Sent from my SM-G935F using...
Just a suggestion, but get your FL die ground a bit so you can bump the shoulder. Body die won't do the shoulder.
If you are worried about case head expansion (I wouldn't worry about a little more...
I have a forster press so no choice in shell holder as such and had similar issues with my AI
I had to get my redding FL die ground as it didn't bump the shoulder at all in my press.
So now all I...
Maybe 150-200 fps more depending on barrel and action. Not (real world) worth it Imo.
I was bored and wanted a project so had one done ages ago.
It turned out primo but there was a lot of learning...
Looks bloody good. Rem brass is probably a good start as it is softer. Also looks to have a sharper shoulder than any of my first time, formed brass.
I might have to get one😆
Sent from my...
Being the mong I am, I would have completely sussed it by looking at it and then proceeded to destroy 30 cases before I bothered reading the instructions. 😆
Sent from my SM-G935F using Tapatalk
40° shoulder?
Sent from my SM-G935F using Tapatalk
My unformed brass is on its way😆
Sent from my SM-G935F using Tapatalk
My body die will still bring them to chamber after 8 or so firings but they won't hold a primer well enough.
Sent from my SM-G935F using Tapatalk
No sorry to confuse.
I am a dinosaur and still use imperial when it comes to reloading.😆
Also case head expansion is the best way to indicate max pressure in an Ackley Imo.
You don't want to...
I would measure the case head with a mic. Anything over .0005 over from a new case I would keep an eye on.
In saying that I could get away with 46grns of RL17 in my rifle.
I stopped using it...
Load so they only require a neck size until the 4-5th go and you will be right. If ya have to bump the shoulder or body size after firing one formed load you are getting up there.
3000 with a 140 is...
I use heaps more AS 30N than that.😆
Sent from my SM-G900F using Tapatalk
43 grns of 2209.
Pretty sure it can handle another grain at least as the shoulders only formed about the same as I can get without projectiles.
Sent from my SM-G900F using Tapatalk
Had a play with my Ackley and FF some cases with projectiles. I have not even tried it with this barrel before so was pleasantly surprised how well it went.
129 gr interlock hard into the lands...
I am surprised you used those words in a sentence regarding a .243😆
Sent from my SM-G900F using Tapatalk
Is that why it only reads pedestrian .243 speeds now?
Sent from my SM-G900F using Tapatalk
Mine sits in the same place if not a tad closer.
Sent from my SM-G900F using Tapatalk
Looking good.
I use a bit more powder to achieve similar velocities but I coat my projectiles.
Sent from my SM-G900F using Tapatalk
Try mag primers with different powders behind the LRAB.
You might get them to shoot.
Sent from my SM-G900F using Tapatalk
Do what works best. Remembering an improved shouldered case will not show pressure signs like a bottle neck.
I only neck size until they get a tadd stiff to chamber an empty. Usually 4-5 goes...
True.
Sent from my SM-G900F using Tapatalk
Have had a .260 imp for a while now and think I have my forming and loads as good as I can get them.
Have formed Lapua, Rem, Norma and Nosler .260 brass.
Rem and Nosler work best in my rifle.
I...