Search:

Trailer legal.
Shuffeled some junk round and now my two car garage has two boats in it!

https://uploads.tapatalk-cdn.com/20171124/d37d1501ac6f2ddf397c3f9c34c0348e.jpg

Just nèed a couple of...

That one has been blasted and arc sprayed.
Technically it's not as good as hot dip but I can have it done just round the road instead of chch and it is quick cheap and easy to get touched up.

I...

Talk about fuck around eh.....busy life so has taken a while.
Just needs safety chain and number plate etc.
...

Good idea for beach launching.
Bit elaborate for what I need and it wouldn't fit in shed.

Sent from my SM-G800Y using Tapatalk

Don't get duratorque!
We are constantly replacing rusted out/failed ones with springs!

Sent from my SM-G800Y using Tapatalk

Yea the pick is a bit deceptive as the drawbeam is cut off from pick.....they are pretty far back....its quite heavy on the "ball" like that with no coupling/winch/jocky wheel yet.
Pretty...

Bloody hell I have been both busy and slack.

Did a little this morning.

Axle and springs back from being arc sprayed.
Assembled and tacked in position (may move yet position is just a guess)...

Yep I hear ya. It is only 11 foot long.
By myself in the 10f parker with the 8 I get 32kph which is starting to get a bit dodgey, two up 38kph in the Tinny Punt felt safe as houses.
Im not really...

Thanks I hope so.

Had a test run with a mate and his 15hp yam last weekend. 250kilo payload not counting fuel and motor weight =WOT 38kph, easy cruise at 27-30 kph.

One thing I did not realise when I built this is...

Yep, a mudguard that cannot be stood on is worse than useless so will be grunty enough to hold my 130kilo mate and as low profile as possible as the dingy will have to sit above them,would be way too...

It is a channel (75 PFC) not an I beam (UB or UC) so 75 high 40 wide, I went with channel toes out for ease of washdown.

A couple of hours into the trailer.

https://uploads.tapatalk-cdn.com/20170624/10a43dc649b045206335abd6898019c4.jpghttps://uploads.tapatalk-cdn.com/20170624/ea570986c74f0a3d1aee05f786a035a8.jpg
...

I thought I saw you and the boss off to poach my flounder spot as I drove up to rocky point, turned out it was a yellow pontoon rib....in my favorite spot....,ah well,I could have set in front of...

She is pretty boyant but dont think she would handel 250 kilos hanging on the transom :thumbsup:

It catches flounder but might need a bit more experience to really get the hang of it.
...

Be a few weeks away yet.
I was going to build an alloy but for the sake of speed of build I am just going to throw together a steel one as basic as possible and get it arc sprayed.

Sent from my...

Yep.....it's now common slang for a single phase portable stick/tig welder.
We have lots of caddys but none of them actually are.

Sent from my SM-G800Y using Tapatalk

Maybe a singlecab flat deck.

Maiden voyage a success, I am very happy at this point.
Stable ! shit yes!.....lower minimum planing speed than the 10f Parkercraft by quite a bit and only dropped around 1-2 kph top speed with the...

Bungs in,transom wood in,seats in.
694696947069471

The Tig or the Mig? the tig is a boc branded ac/dc.

https://www.boc.co.nz/shop/en/nz/boc-smootharc-185-hf-dc-tig-welder-boc185acdc-fc-p

Its a nice little single phase unit for the money but be...

All depends what you are doing with it?
Small jobs you will do 6mm easy but the handpeice wont handle 180amp constant and neither will the powersource.
If 4mm is about as thin as you would use I...

The single phase caddy? yep welded all the pontoons with it.....110-115a AC 5% positive, that is realistic maximum for continuous welding with it with a 2.4 tungsten and a no cooled torch. I rate it...

Yes seats as per earlier in the thread but not fitted yet.