Blaser r93 and r8

[tui_man2]

As few would know how done some of these a while ago one of which played up so was changed other 2 where fine and still go fine as well.

Since then have gone bit more to the drawing and nutted them out and tightened them up also with little flaws on prototypes but they where ironed out with little program changes. Have 5 93s on mates ones getting tubes worn out faster then hooker poles :rolleyes:

The r8 in a machining mind is a whole lot better system tho nothing changes other then size and shape of the collet its just easier.

A lot of receivers where chopped up an checked for fits and playing around with small shape changes.

But not they are away an done here are some of what they look like, these ones are blasted stainless finish, and one photo with the r8 still to be blasted, also have another 2 getting coated black as well.

Can do them with standard saddle mounts or drill and tap for a rail, rail can also have angle milled into it as well.

With the beauty been you can get the cal an twist that you want an then if you burn it out its a fairly standard rebarrel simular to a factory rebarrel but little more involved still same amount of time.

Will have a r8 chambered in 7mm gonzo that can be sent around to genuine people with interest in the system with dies an brass to try for themselfs, an can supply all Blaser parts also.

Will add more here so watch the space Blaser owners.



Sent from my GT-I9300T using Tapatalk 2

[sneeze]

Will have a r8 chambered in 7mm gonzo that can be sent around to genuine people with interest in the system with dies an brass to try for themselfs, an can supply all Blaser parts also.

Im sure they both will be.
Gotta say naming a chambering after a muppet

[tui_man2]

Im sure they both will be.
Gotta say naming a chambering after a muppet

someone clicked on haha
Its good been outside the box :thumbup:

Sent from my GT-I9300T using Tapatalk 2

[sneeze]

[45SOUTH]

What have you done with my one

[R93]

What have you done with my one

I seen it today. He was using it to jimmy a huge chuck off the lathe.



Sent from my iPhone using Tapatalk 2

[Neckshot]

As few would know how done some of these a while ago one of which played up so was changed other 2 where fine and still go fine as well.

Since then have gone bit more to the drawing and nutted them out and tightened them up also with little flaws on prototypes but they where ironed out with little program changes. Have 5 93s on mates ones getting tubes worn out faster then hooker poles :rolleyes:

The r8 in a machining mind is a whole lot better system tho nothing changes other then size and shape of the collet its just easier.

A lot of receivers where chopped up an checked for fits and playing around with small shape changes.

But not they are away an done here are some of what they look like, these ones are blasted stainless finish, and one photo with the r8 still to be blasted, also have another 2 getting coated black as well.

Can do them with standard saddle mounts or drill and tap for a rail, rail can also have angle milled into it as well.

With the beauty been you can get the cal an twist that you want an then if you burn it out its a fairly standard rebarrel simular to a factory rebarrel but little more involved still same amount of time.

Will have a r8 chambered in 7mm gonzo that can be sent around to genuine people with interest in the system with dies an brass to try for themselfs, an can supply all Blaser parts also.

Will add more here so watch the space Blaser owners.



Sent from my GT-I9300T using Tapatalk 2

I don't have enough money but can I just say that rifle looks the bisness the vx6 suits a blaser I think.Nice rifle abe.

[tui_man2]

What have you done with my one

Will add more soon I have to take better photos to do these justice

[outdoorlad]

Looks shit hot, PM inbound

Does the rail allow the scope to be mounted back far enough?

[tui_man2]

Looks shit hot, PM inbound

Does the rail allow the scope to be mounted back far enough?

Just mate on the ones I have done but have changed that a little to with a made rail now that will over hang to give more room to

Pm replied

[tui_man2]

I never looked at how shitty the photos where. Will do some more better ones.
Here is the R8 version

[Toby]

Does that one have a tilted rail?

[Friwi]

So basically are you using the sleeve of an old blaser barrel or are you building those barrels from scratch?

Thanks.
Friwi

[kiwijames]

Blasers are shit. I'm drunk and off to a titty bar but still know they're shit. Just ask me.

[tui_man2]

So basically are you using the sleeve of an old blaser barrel or are you building those barrels from scratch?

Thanks.
Friwi

Can use the sleeve of your worn out barrel if you wanted, but these are from scratch, match barrels an fit them to my receiver

Does that one have a tilted rail?

Yea mate has 17moa milled into it to get the scope down bottom end of travel