Printable View
I feel I could be opening a can of worms here ?? Ahhh wth :)
I'm reloading for a mate . People's thought s I'm going with Hornady 130 gr sst
I ve loaded 10 of each and yet to test them probably Goin around it the wrong way in fact I am but wtf so 10 x 54 gr of AR 2209
10 x 45 gr AR 2206h
10 x 58 gr AR 2213sc
As those the only powders I use in any of my reloads
So horse's for courses
What maybe my best option and what are yours ?? For what reasons?
Sent from my SM-G920I using Tapatalk
Frankly I would have just used 2209 and done different powder charges in 0.5gn increments.
As it is, you are guessing that the 54gn is going to get a good result and same with the 2206H (too fast IMO) and 2213.
PS, key to loading for another rifle is the head space and setting the dies up properly.
Was the brass from his rifle?
no its not ....yeah I know I should ve been working it up ,, just playing atmQuote:
Originally Posted by dogmatix
2209
With 2209 load in 1 gn increments from 52 to 56 gns with a 130. load 2213 from 57 to 61 gns in 1 gn increments.
Some long throated .270's will take a couple grains more 2213. If it was me, I'd load 1 of each and do a "ladder test" at a range of at least 100 meters. Look for the loads that shoot close to each other and then load that charge and loads of 0.5 of a grain on either side of that charge.
Save the 2206h for a .223 or .308
Run 58gr 2213c with Barnes 130 TTSX and 59gr with 110gr TTSX.
Stop with the 2206, now, right now!
You have two other powders that work in .270, so choose one, and pick a start load.
Test that load until you confirm it does or does not work, altering only seating depth.
2213 (H4831) is the traditional number one .270 powder, I would start there.
Not sure about the 130 SST in .270, wouldn't use it myself, but to cross reference possible rifle preferences also test a projectile with a different form factor, such as 130 Sierra Prohunter if 130gn is the weight you are stuck on..
The PH will likely need to be seated 60-80 thou deeper than the SST's optimum depth, assuming you find one.
AR2213sc does the bizo for me in the .270
the 2206 keep for smaller cases its ok but not as good as the other in .270
130s for open country and say a 150 grn partition for in the scrub or roaring big stags up close and he will be set.
ok so you have FL resized for him...that's ok, a partial length resize from here on out might be just the ticket (works for me)
SST???? don't know haven't tried them...whats he wanting to shoot???? goats and wallabies fall over with just about any load,just poke pill through shoulders "ya cant drive a car with no front wheels" for fallow you wont need a super hard pill either but if looking at mainly reds and/or pigs I would be a little more picky
130 Nosler ballistic tips or 130grn speer spfb are my open country loads and 170grn speers (no that's not a typo) for the bush.
Thx everyone for your help full advice all has been taken on board will stop using the 2206 .. felt that the 2213 is the best for the 270 from the beginning .
The rifle is his late father's and understandably won't get rid of it . He may not use it for much Hunting just wants to work up a load .get it shooting straight .which may also mean a new scope ... another can of worms ...
I'm just trying to point him in the right direction and give him the best advice possible
Sent from my SM-G920I using Tapatalk
I've loaded those Hornady SST for my Rem700. Seat to the cannelure. Load info in the thread below. Love their accuracy.
http://www.nzhuntingandshooting.co.n...ady-sst-23196/