Suggestions on supersonic cleaning cases after resizing as opposed to normal cleaning methods.
Printable View
Suggestions on supersonic cleaning cases after resizing as opposed to normal cleaning methods.
I purchased an rcbs ultrasonic but subsequently purchased a Frankfort rotory tumbler.
Best reloading accessory I've ever purchased. If your loading large numbers of cases then that's the way to go.
You don't even need stainless pins for cleaning. You just chuck in the cases, add a half teaspoon of citric acid and a squirt of morning fresh dishwash liquid and set for half an hour. They come out like new.
The only benifits of the ultrasonic are that you can also clean gunparts
+1 on the rotary. I only use my ultrasonic for parts cleaning now and it does a good job especially on AR bits. Never did that good of a job on brass and is no comparison to the rotary for results on brass.Quote:
Originally Posted by omark
Sent from my SM-G935F using Tapatalk
Thanks for the input. Had a bit of brain fade when I said supersonic instead of ultrasonic. The Frankfort sounds like the way to go. Does it clean the insides including flash hole area etc. pretty well? So just the two liquids and nothing else and away you go?
Yup pretty much. I add a bit of car wash as well, keeps the cases from tarnishing afterwards too. The Frankford Arsenal one has a great system with mesh ends for separating the pins from the brass after cleaning. This is a super handy feature: Separating 1200 223 cases from pins can be a total ball-ache, their magic system does it in a few minutes, which you do while rinsing anyway.Quote:
Originally Posted by BSA270
Brass comes out like new with insides shiny and flash holes perfect.Quote:
Originally Posted by BSA270
Some pistol brass is harder to clean the older it gets but rotary tumbling is the only way to go. You can also identify faults a bit easier with really clean brass.
I do get tarnished brass every now and then if not used for a while even tho rinsed thoroughly. Will try @Tommy idea to see if that will make a difference.
Sent from my SM-G935F using Tapatalk
It's great to wash your fired brass first if you possibly get unwanted pickup brass mixed up with yours.. Like that twin flashole milsurp rifle stuff, or that weird maxx tech 9mm (or whatever the brand is) with the thick case walls and the step below the case mouth. The first step in culling it out before you put it through a sizer and damaging your gear is to be able to see it, and it's harder to see if it's dirty. I clean mine with or without pins first, half an hour, dry, and check for stuff to biff. Then lube and size, and back in with the pins. Dry it and it's ready to go, and super shiny.
Where did you buy your rotary tumblers?
Sent from my SM-G950F using Tapatalk
I got a 3kg rock and jewelry tumbler from aliexpress. Think it was just over $100 nz dollars.Quote:
Originally Posted by Tikka7mm08
Had it 3 yrs and it hasn't missed a beat with a lot of use.
When/if it shits itself I will just buy another.
I can do 200 pistol brass or 100 223 cases at a time. Not as much capacity as a frankford one but suits me fine.
Sent from my SM-G935F using Tapatalk
Did it come with stainless media?Quote:
Originally Posted by R93
Sent from my SM-G950F using Tapatalk
No. Come with stainless pellets/balls tho.Quote:
Originally Posted by Tikka7mm08
I bought the pins separate from the states.
Got 3kg of pins for 30 bucks and I am still on the first bag of pins. I doubt they will ever need replacing unless I lose them over time sifting them from the brass.
Sent from my SM-G935F using Tapatalk
Brownells when they are on special
Thanks for the car wash tip. I shall try it.
To remove pins (if you should use them) and also to thoroughly wash the brass post tumbling I would highly recommend the Frankfort arsenal basket which sits on top of a 20 litre bucket. You fill the bucket with water, drop the brass into the rotory cage which sits on the top and then turn the handle.
Another great invention which has saved lots if time and hassle
With the new Frankford Armory one, you don't even need the separate sifter, it has attachments. I had one I bodged up that I used for a few years, ran it in the lathe at work. Don't work there anymore so have been building another but needed one in a hurry so bought the FA one. Would highly recommend it. If I was to build another I would buy a FA drum separate (you can buy them), which isn't expensive, and make the drive mechanism.
