Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

ZeroPak Alpine


User Tag List

+ Reply to Thread
Results 1 to 15 of 52
Like Tree6Likes

Thread: First attempt at necking down 308 to 7mm08

Hybrid View

  1. #1
    Lovin Facebook for hunters kiwijames's Avatar
    Join Date
    Feb 2012
    Location
    Hawkes Bay
    Posts
    7,283

    First attempt at necking down 308 to 7mm08

    Quote Originally Posted by RimfireNZ View Post
    Damn it, I was in a rush so no didn't chamfer it. There's part of the problem. I was doing half a dozen other things after coming back from the range and dropping a bullet in was an afterthought. And no the seating die isn't set too low on this one.

    When you actually site a projectile in the necked down 308 brass, then do the same with the 7mm08 round you can really see that the round isn't gonna fit in the necked down 308. It needs trimming on the inside. I'll measure it up tomorrow when I'm back over there.

    My house is too small so my reloading room is at my folks in town.
    Unless you are not using your expander in the FL die you will always need to outside turn if things are tight. 243 7-08 308 all going to form internally to the expander used not the die. Something looks proper fucked up with your cases. What's dies?
    veitnamcam likes this.
    The range of what we think and do is limited by what we fail to notice. And because we fail to notice that we fail to notice, there is little we can do to change; until we notice how failing to notice shapes our thoughts and deeds

  2. #2
    Member RimfireNZ's Avatar
    Join Date
    Mar 2012
    Location
    Auckland, New Zealand
    Posts
    553
    Quote Originally Posted by kiwijames View Post
    Unless you are not using your expander in the FL die you will always need to outside turn if things are tight. 243 7-08 308 all going to form internally to the expander used not the die. Something looks proper fucked up with your cases. What's dies?
    Just the basic Lee ones for 7mm08. I took out the decapping pin and I assume that's the expander? I can't actually resize the cases with that in. It doesn't get all the way in.

    Take it out, put them through the fl die, then they measure up at least externally, but not internally.

    Let me get some proper measurements for you guys tomorrow. Maybe that'll give you some more idea of what's going on.


    This shouldn't be this hard, but i've only done factory ammo reloading before for a few calibers. That's easy cos you only need two dies and once it's set up, that's it

 

 

Similar Threads

  1. necking down lapua .308 to 7-08
    By yerimaginaryM8 in forum Reloading and Ballistics
    Replies: 10
    Last Post: 20-04-2014, 11:49 PM
  2. Necking down 308 to 7mm08
    By RimfireNZ in forum Reloading and Ballistics
    Replies: 26
    Last Post: 31-12-2012, 05:22 PM
  3. The mans gun - 7mm08
    By crnkin in forum Firearms, Optics and Accessories
    Replies: 23
    Last Post: 08-04-2012, 12:35 PM
  4. 7mm08 to 260
    By DAVE.H in forum Reloading and Ballistics
    Replies: 8
    Last Post: 27-12-2011, 09:53 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!