I was wondering if any body on the forum has got a good accurate load for this rifle that will run about 1/2 moa.
I Prefer adi powders and hornady projectiles as easy to get most of the time.
Cheers Andy
Sent from my GT-I9300 using Tapatalk
Printable View
I was wondering if any body on the forum has got a good accurate load for this rifle that will run about 1/2 moa.
I Prefer adi powders and hornady projectiles as easy to get most of the time.
Cheers Andy
Sent from my GT-I9300 using Tapatalk
60g vmax
26g of 2208
Never mind calling me @andyanimal31 !
Got several good 1/4-1/2 MOA loads with 2206h
69 targex going really well
Cheers for that 7mm.Quote:
Originally Posted by 7mmsaum
Have ya tried the vmax on goats or the like?
Sent from my GT-I9300 using Tapatalk
Lol I forgot about ringing you the 223 god!Quote:
Originally Posted by robh500
Never owned a 223 as have had the big brother for a few years.
The cartridge just doesn't look like it can hold enough powder!
Sent from my GT-I9300 using Tapatalk
Yes definitely, the 60g v-max like the 60g nosler ballistic Tip has a hard thick base which gives it good penetration on realistically angled shots into the vitals.Quote:
Originally Posted by andyanimal31
Neck sizing only gives your brass extra capacity
6mmbr website has a page in the menu dedicated to the 233 and has a chart of the worlds brass in order of most internal capacity to the least
Proper brass selection, neck sizing only and seated out projectiles can give you reasonable case capacity -and the right combo with 2208 powder can get 3200fps with a 60 grainer.
2206H can give a useful boost with ammo of a shorter over all length
Good bit of info thanks.Quote:
Originally Posted by 7mmsaum
I got the powder just need to get some projes.
I run the 52 amax in my 22-250 with great results
Sent from my GT-I9300 using Tapatalk
The 52 amax and 55g gameking are good projectiles, they are shorter than the 60g as well which further increases powder capacity
The difference being 1/2 a grain of 2206H
Which is quite a bit, often 100 fps when up at a full case
You already know to work your way up to this level of performance looking for the usual pressure signs
50gr z or a max
Adi brass
2206h 26.5gr (need a drop tube)
15 thou jump
Fed 205 primer.
3400 fps.
Usual safety warning work up to it.
Which of bm2 or 2206h would be denser and make the most of the limited capacity? Or are they much of a muchness? I have two loads using 2206h, but I'm told bm2 will go better through my Lyman 55 than the yuk crunch of the 2206h so keen to have a play
What are you shooting? Targets? Small or large animals?
I have a 1:7 Savage Model 12 .223 with 26" barrel.
For target shooting I load 24.7 gr 2208 in Norma cases with 80 gr A-Max projectiles.
Good out to 800 yards, up to 1000 in light winds.
Hornady 60grn. Vmax and 60grn. HP are both great accurate bullets . . . Vmax is spectacular on Goats/Fallow but a little pricey - the HP is cheaper and just as accurate with the same POI out to 400 as the Vmax with my .223 - brilliant on Hares at longrange
I shot 55gn Blitzkings with ADI 2206h through mine.
http://i27.photobucket.com/albums/c1...n/P9141483.jpg
Never tried anything else, as moved back to a lighter sporter.
65gr gamekings 23.5gr BM2 57.2mm oal is my goat and fallow round.
75gr Amax 25.5gr 2208 61mm oal is my long range rabbit and hare round.
Both shoot to the same POI in my savage.
75 grain Amax and 24.5 grians of 2206 in mine.
1/2" 5 shot groups and no problems at either end of the system. I had to lengthen the mag box to get the projectiles out near the lands though.
How did they shoot mag lenghth as some projectikws dont mibd the jump.Quote:
Originally Posted by Ross Nolan
Thats as long as it doesnt take up to much powder space!
Sent from my GT-I9300 using Tapatalk