Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

Alpine Terminator


User Tag List

+ Reply to Thread
Page 1 of 2 12 LastLast
Results 1 to 15 of 21
Like Tree63Likes

Thread: Reloading 6.5x55

  1. #1
    Member Shearer's Avatar
    Join Date
    Sep 2013
    Location
    Tasman
    Posts
    7,019

    Reloading 6.5x55

    What sort of performance would you expect form the old cartridge in a modern firearm?
    Moutere likes this.
    Experience. What you get just after you needed it.

  2. #2
    Member
    Join Date
    Aug 2018
    Location
    Christchurch
    Posts
    1,647
    Same performance as a Creedmoor.
    Resident 6.5 Grendel aficionado.

  3. #3
    Member
    Join Date
    Jul 2012
    Location
    Invervegas
    Posts
    5,149
    Last time I ran one (one of many over the years) I ran Sierra 130gn TMKs with 48.1 of 2209 for an honest 2900fps. Tikka T3, Lapua brass and shot beautifully. As always work up, this load would be too hot for a '96
    Shearer and blip like this.

  4. #4
    Member
    Join Date
    Mar 2012
    Location
    Christchurch
    Posts
    1,411
    Tikka 595 (22 inch barrel), RL22, 139gr Hornady. Most accurate load around 2750ft/sec.
    Shearer and rewa like this.

  5. #5
    Gone................. mikee's Avatar
    Join Date
    Aug 2012
    Location
    Nelson, New Zealand
    Posts
    9,808
    Quote Originally Posted by Pommy View Post
    Same performance as a Creedmoor.

    Better performance than a Creedmore, more capacity. Under rated, in a modern rifle with modern barrel they are bloody good (but not trendy)
    HUNTY, Fisherman, zimmer and 7 others like this.
    Trust the dog.........................................ALWAYS Trust the dog!!

  6. #6
    Member norsk's Avatar
    Join Date
    Jun 2016
    Location
    Norway
    Posts
    2,541
    Quote Originally Posted by Shearer View Post
    What sort of performance would you expect form the old cartridge in a modern firearm?
    It depends on what you are after? As a "bang flop" cartridge I think a 308 has the edge,for flat shooting and mild recoil/little blast the old Swede is hard to beat. I have a couple and have had a few,they are cheap to reload for,have decent case life and a good choice of projectiles.

    Over here they call the 6.5 Creedmore the "6.5 Costmore" as it dosnt do anything the 6.5 cant do except fit in a short action.
    "Sixty percent of the time,it works every time"

  7. #7
    Member andyanimal31's Avatar
    Join Date
    Dec 2011
    Location
    Makakahi road Raetihi
    Posts
    3,662
    The God of chamberings!
    On my third factory barrel on my tikka.
    I have swapped from the 143eldx to the 147eldm.
    2720 and is more accurate than I can shoot.

    Sent from my SM-A226B using Tapatalk
    BRADS, Shearer, Woody and 4 others like this.
    My favorite sentences i like to hear are - I suppose so. and Send It!

  8. #8
    Member
    Join Date
    Dec 2011
    Location
    NI
    Posts
    12,716
    Have used mine a bit again recently. A modern Schultz and Larsen. n560 powder and 140 Amax (or gold dot). 21.5" barrel. 2840 fps.
    Out beyond ideas of wrongdoing, and right-doing, there is a field. I will meet you there.
    - Rumi

  9. #9
    Member
    Join Date
    Dec 2019
    Location
    Okawa Hawkes Bay
    Posts
    3,039
    Quote Originally Posted by Tentman View Post
    Last time I ran one (one of many over the years) I ran Sierra 130gn TMKs with 48.1 of 2209 for an honest 2900fps. Tikka T3, Lapua brass and shot beautifully. As always work up, this load would be too hot for a '96
    That load would be far too hot for any rifle with todays AR2209 which is significantly faster than the pre 2000 stuff.
    Regards Grandpamac.
    rewa likes this.

  10. #10
    Member
    Join Date
    May 2016
    Location
    Blenheim
    Posts
    1,155
    My Tikka loves both 139 Scenar and 143 eldx. Pic shows eldx @ 100.Name:  IMG_0137.jpeg
Views: 246
Size:  1.48 MB
    Tahr, zimmer, Shearer and 4 others like this.

  11. #11
    Member
    Join Date
    May 2016
    Location
    Blenheim
    Posts
    1,155
    And 139 Scenar. I reload using Lapua brass, ADI 2209 powder and Winchester primers (as all I could find at the time)Name:  IMG_0136.jpeg
Views: 239
Size:  1.92 MB
    Shearer, Swanny and rewa like this.

  12. #12
    Member
    Join Date
    Dec 2019
    Location
    Okawa Hawkes Bay
    Posts
    3,039
    Greetings All,
    I did quite a bit on this a few years back which I wrote up in a couple of articles in NZ Guns. The Hodgdons data seemed to fit the powder I had well including my older AR2209 but the pressures were low. My current lot of AR2209 gave close to 100 fps more velocity than the older lot, equivalent to 2 more grains of powder. The 129, 130 grain projectiles seem to give decent velocity in the mid 2,800 fps range. Will look out my notes and post more later.
    Regards Grandpamac.
    Shearer, Ingrid 51 and rewa like this.

  13. #13
    Member
    Join Date
    Jun 2023
    Location
    waimakau
    Posts
    3,579
    Grandfather of the 6.5s

  14. #14
    Member
    Join Date
    May 2020
    Location
    Palmerston North
    Posts
    266
    With the CIP max pressure of 55,100psi. ~2750fps with a 23" barrel, 140gr projectile, and single base powders like AR2209.
    3" of barrel is ~100fps unless you're shorter than 20".
    -10gr of projectile weight is ~+100fps.

    Your best bet is to estimate performance with Gordon's Reloading Tool or Quick Load.
    Shearer likes this.

  15. #15
    Member
    Join Date
    Jul 2012
    Location
    Invervegas
    Posts
    5,149
    Quote Originally Posted by grandpamac View Post
    That load would be far too hot for any rifle with todays AR2209 which is significantly faster than the pre 2000 stuff.
    Regards Grandpamac.
    Current 2209. My load workup was done with a fully calibrated GRT calculation, running at a calculated 62,000 psi, well within the limits of brass and rifle, even though over "book max" As I mentioned very important to work up and be aware of all factors when going above book max (which I dont make a habit of but the 6.5x55 just cries out for it). A previous modern 6.5x55 (a Heym SR-20) that I ran in the early '80s never got to this velocity with 130 as the tools (GRT) just weren't available then, and the ones we had like the Powley conputer (an internal ballistics calculator like a slide rule, and there was a paper based one too) were not sophisticated enough to fully explore anything above "book max".
    nor-west, zimmer and Shearer like this.

 

 

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!