Printable View
Just started breaking in the barrel of my 7mm rem mag using federal blue 150grn, shown is the first group ( shots 9,10,11 ) the first shot of the group is out of a thoroughly cleaned, cold bore. Real pleased that the first shot is centre of the next rounds. Scope is a Leupold mk4 4.5-14x50 - Courtesey of KIWI JAMES, on a egw rail, leupold pwr rings fired of the bonnet of my vitara using a bag of grass seed and a harris bipod. Shit I love these Tikkas.
Attachment 5715
Rifle
Attachment 5717
They are good alright VTF,
They often like the "go to" accuracy load for the Rem Mag/A-Max combo which is..
162 A-Max
72g of ADI 2217 powder
Federal 215 primer
A Cartridge over all length of 3.345 inches to fit the magazine.
This combo gives 3030 - 3050 fps in long throated rifles like Tikkas and Sakos, and stunning accuracy.
As at last week Beretta was out of Tikkas in 7mm rem mag and Gun ity had sold out, Dave Craft at 'Craftys Rods N Guns' in Hastings has what could be the last one in NZ at the moment ($1200).
Id say, if you can only have one rifle/caliber combination (for deer) to chose from then make it a T3 or Finnlight in 7mm Rem Mag. Load it down for softer recoil or tune it up for LR.
PS. Im a little reticent to add a disclaimer here for Blaser owners in their blazers.
Where's the biting my tongue smiley?
Next to the 'hook line & sinker' smiley :)
Ha ha ha two very good comments
Envious. Much.
Cheers for the load data, I have some 2217 left over from a 338 lapua, just have to order some dies and projectiles.Quote:
Originally Posted by 7mmsaum
I have the same combo except put a waitaki engineering brake on it and optilock rings.
I am using 72.5 gns of 2217 and its doing 2980 fps but there is signs of pressure with flat primers and ejector marks on the brass.
Will back it off with the next reloading but cant get the velocity up over 3000 fps which is what i would like to have got out of it.
I will use 2225 next time i get powder to find out if it suits better.
Yeah , Iv heard 2225 is the go to powder for the 7mm rem mag or even better IMR7878. Will go with the 2217 and see how it goes.Quote:
Originally Posted by yogi
First Blood , red shot last night after milking. Only saw part of her throat and lower jaw after spooking her , bullet went straight through the throat at 210m - stoked.
Attachment 5845
Sweet.
Sent from my GT-S5360T using Tapatalk 2
No mucking around just the way we like it :cool:
Brilliant VTF. Looks like the rifle and the load work well for you.
Thatll fuck her
Sent from my GT-I9300 using Tapatalk 2
I tried 2225 and 2217. prefer 2217. seemed to give more consistent results with Amax although 2225 worked fine with bergers
Cheers Hori, waiting for dies at the moment, then Il be into it.Quote:
Originally Posted by horihunter
Hi everyone, just arrived in this forum where i have a lot to learn from.
I been reloading for my 2x 7mm rem mag and i have a great result with the following load on them, ADI2217 at 69.5gn, federal 215 primer and mixed brass(winchester, remington and hornady) sitting at 3.280". My Tikka T3 Lite don't fit bullets longer than 3.300" and my grouping with my load is in between 1/2-3/4" at 100mts.
This load has also worked PERFECTLY with 1/2" on a Sako Finnlite without "any" alteration. Hit a A4 size plate at 550mts with this load.
Please, will love to hear more about loads for this caliber.
Welcome to the forum. Enjoy.
?
Ive used 2217 with all the 7mm mags I've had and the current one likes 162amax 74gs 2217 going at 3080fps primers just starting to flatten out no brass marks etc.
I realise this is a hottish load but it just seems to work :)
Thread revive. @burtonator that was the same load I went with (CCI mag primers/Win brass) in my HS Precision - shot 0.5" all day. My Sendero before it loved 71.5gn 2217 same bullet, swapped load to the HS and ended up pulling a bullet out when unchambering an unfired load. The new HS load was then seated deeper and the 74gn showed no pressure signs and shrunk the groups.Quote:
Originally Posted by burtonator
