Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

Delta ZeroPak


User Tag List

+ Reply to Thread
Results 1 to 12 of 12
Like Tree3Likes
  • 3 Post By kokako

Thread: Sako 85 threading question...

  1. #1
    Full of shit Ryan_Songhurst's Avatar
    Join Date
    Sep 2015
    Location
    South Island
    Posts
    10,207

    Sako 85 threading question...

    Im looking at purchasing a Sako 85, im looking at the finnlight as I like the idea of an all weather rifle. Im going to stick with 270 win and was wondering if I will run into trouble cutting the barrel to 20" and threading for a suppresor? I have heard that the factory fluting can affect cutting and threading these rifles?

  2. #2
    Member
    Join Date
    Jan 2012
    Location
    Wallacetown
    Posts
    449
    i stopped the thread about 5mm from fluting,have done this on 3 finnlights no problems at all.
    hunty
    6.5x55AI

  3. #3
    Member
    Join Date
    Jun 2013
    Location
    Middle Earth
    Posts
    4,030
    I cut into the fluting and thread quite often. Done many fluted tikkas and sakos downs to 16" or 15", no issues.

  4. #4
    Full of shit Ryan_Songhurst's Avatar
    Join Date
    Sep 2015
    Location
    South Island
    Posts
    10,207
    Quote Originally Posted by HUNTY View Post
    i stopped the thread about 5mm from fluting,have done this on 3 finnlights no problems at all.
    I want to chop 2 inches off the barrel so it will end up into the flutes

  5. #5
    Full of shit Ryan_Songhurst's Avatar
    Join Date
    Sep 2015
    Location
    South Island
    Posts
    10,207
    Quote Originally Posted by Friwi View Post
    I cut into the fluting and thread quite often. Done many fluted tikkas and sakos downs to 16" or 15", no issues.
    Thanks for that Friwi, how does the rear bushing setup work if using an overbarrel?

  6. #6
    Member
    Join Date
    Jun 2013
    Location
    Middle Earth
    Posts
    4,030
    Simple, rear bush hole is opened to the outside diameter of your barrel where it contacts at the rear.

  7. #7
    Member kokako's Avatar
    Join Date
    Apr 2012
    Location
    Nelson
    Posts
    923
    Quote Originally Posted by Ryan_Songhurst View Post
    Im looking at purchasing a Sako 85, im looking at the finnlight as I like the idea of an all weather rifle. Im going to stick with 270 win and was wondering if I will run into trouble cutting the barrel to 20" and threading for a suppresor? I have heard that the factory fluting can affect cutting and threading these rifles?
    If your going to hack the barrel up why don't you just get a Synthetic Stainless? $200-300 cheaper than the Finnlight too.
    crewe2, BRADS and Mathias like this.

  8. #8
    Member
    Join Date
    Jan 2012
    Location
    Wallacetown
    Posts
    449
    Quote Originally Posted by kokako View Post
    If your going to hack the barrel up why don't you just get a Synthetic Stainless? $200-300 cheaper than the Finnlight too.
    yep that would be the go, and if you want to sexy it up you can get that barrell flutted at a later date, shouldn't cost as much as only half a barrell
    hunty
    6.5x55AI

  9. #9
    Member
    Join Date
    Jun 2013
    Location
    Middle Earth
    Posts
    4,030
    Unfortunately, fluting a short barrel or a long barrel take almost as long and is charged therefore the same.

  10. #10
    Full of shit Ryan_Songhurst's Avatar
    Join Date
    Sep 2015
    Location
    South Island
    Posts
    10,207
    Well I have bought a finnlight in 270wsm now, its allready threaded and is at 22" (factory) im not sure if I should give it my signature 270 20" treatment or leave it as is......now i need to decide on a supressor, im thinking DPT overbarrel?

  11. #11
    Member kokako's Avatar
    Join Date
    Apr 2012
    Location
    Nelson
    Posts
    923
    Leave it at 22"

  12. #12
    Full of shit Ryan_Songhurst's Avatar
    Join Date
    Sep 2015
    Location
    South Island
    Posts
    10,207
    Quote Originally Posted by kokako View Post
    Leave it at 22"
    Yes, seems like I was wrong and the factory length is actually 24", will definately be bringing it back to at least 22" though

 

 

Similar Threads

  1. Suppressor threading
    By Gerbs in forum Firearms, Optics and Accessories
    Replies: 24
    Last Post: 11-01-2016, 10:25 PM
  2. Sako Optilock Ring Mounts height question
    By SlimySquirrel in forum Firearms, Optics and Accessories
    Replies: 11
    Last Post: 19-10-2015, 07:14 AM
  3. Double threading. Is it just me?
    By mcche171 in forum Questions, Comments, Suggestions, Testing.
    Replies: 21
    Last Post: 10-11-2014, 08:25 PM
  4. Sako 85 synthetic stock bedding side wall contact question
    By Bagheera in forum Firearms, Optics and Accessories
    Replies: 2
    Last Post: 19-04-2012, 01:13 AM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!