Printable View
So with all these custom rifles coming up in the buy, sell section of which I cannot afford it got me thinking. I have an xbolt that I have spent far too much on in 7mm mag, but I love it. Question is, in the long run once its shot out can it be rebarreled to 7mm stw or another caliber off that bolt face? Its had a bit of a hard life with reloading before I owned it but its accuracy is mint for the time being so this will be a future endeavour.
I imagine you could re barrel into something like a 7 blaser mag. That’s what I’m thinking of doing to my tikka rem mag.
Quote:
Originally Posted by stagstalker
That's my thoughts, just didn't know if the xbolts are finicky or if I'd have issues.
stw is possible with the bolt face yes
the mag will need to be an inch longer so see if theres enough there or if it will be single feed
you can also just ream your current barrel to 7STW
Gun smiths don't like re-barreling the xbolts. Something to do with them having a very fine thread and being very difficult to get off. Google the topic and you will see.
Maybe more internet rumor than fact, have had barrel's removed from 3 without any drama, two for threading, one to change to a Brux 1:8. Correct tooling is a necessity; like most precision engineering excessive force in place of good technique often leads to disaster.. One well known gunsmith told me he had caused some damage to one when removing the barrel to find the cause being over-length base block attachment screws bottomed out on the barrel tenon. When fitting mounts/bases to x-bolts always check the screw length, Talley's are often over-length on the forward mount, not only has this the potential to cause the problem mentioned above but also to negatively affect accuracy.
If the 7RM barrel is long enough to get the velocity out of it that you want and isnt worn out a simple rechamber would likely not cost more than 200 for the whole service
Opinions. eh. I tried to get one done by a well respected smith and that's what he told me so I left it.Quote:
Originally Posted by 38 South
I'd say the only issue is mag length, I dont have a lot of room to spare with my handloads as it is. The barrel has already been taken off so no issues there. Just want to know there's options down the track once the barrel loses accuracy. I've seen a fair bit has been done with the a bolts. Just love the rifle and dont wanna part with it
When i rebarrel my abolt people said not possible fine threads etc some said blued actions were better than ss ones for rebarrel i had my old barrel releif cut
So was easier to remove so less chance of stuffing fine threads
So far so good after a few years
They do have very fine threads but I have seen Dean Maisey do a few of them so could be smith dependent, I know he said they were a pain in the arse but definitely do able,
Who did the work on yours? I've found one gunsmith that is happy to do mine, a couple weren't too enthusiastic about it howeverQuote:
Originally Posted by 38 South
Check you PM's
I had Arther Cleland do one for me years ago no problem.Quote:
Originally Posted by cameronjackwhite
Sent from my SM-G920I using Tapatalk
Hes one of the ones that has said it's no problems. He also did my 284 so I have a bit of faith in himQuote:
Originally Posted by 25/08IMP
Yea he's a good old gunsmith.Quote:
Originally Posted by cameronjackwhite
Sent from my SM-G920I using Tapatalk
Any smith that has an issue with a fine thread shouldn't be a smith
Arthur has done a few jobs for me over the years including re barrels, fast efficient service great to deal with.Quote:
Originally Posted by 25/08IMP
Dean re-barreled my A-Bolt to 6.5 SLR, shoots as good as my Stiller Predator. A-bolt/X-bolt are great actions, super fast cycling with 60 deg bolt throw.
Just pitty there arn't many after market parts
It should take you a while to wear out 7mmRM barrel under normal hunting use conditions :pacman:
If/when you do so and you want to re-barrel then +++++1 for the 7mmBM especially if your cramped for mag space.
But options for semi custom and parts, stocks etc much better if you went with REM700 or Tikka.
Good advice and the route I ended up taking, have a rem700 30nosler being built at the moment. Parts were alot easier to source now and in future.Quote:
Originally Posted by chainsaw