? king pin bearings hold the hub on and wheel bearings hold the wheel on,cv only transfers torque and should play no part in holding the wheel on!
Sent from my GT-S5360T using Tapatalk 2
Printable View
Correct, first inspection looks like those 54mm nuts that tighten and hold the bearings and hub on have stripped themselves leaving nothing but the cv supporting the weight of the wheel via the drive hub which then snapped the cv at the wheel end of the cv like a carrot.
So at the moment wheel is only supported by the way the hub assembly keys in by 20mm and the rotor and caliper are the only things stopping it from coming out.
Will take some photos for you when I pull it apart today.
When it first happened we thought it was just the cv and had to drive it through some real shit stuff to get back. Hopefully that didn't cause too much extra damage.
Oh nasty.
Sent from my GT-S5360T using Tapatalk 2
Yeah not ideal
Hoping new cv, bearings and this http://www.trademe.co.nz/Browse/List...x?id=764244336 is all it needs. Fingers crossed the spindle is all good :(
@veitnamcam, spindle is fooked. As my mate said, snapped like a carrot. Be real nice to have some axle stands @Savage1
Attachment 27998
Bugger! Probably find better aftermarket ones cheaper than genuine, As mentioned factory bearing fits are on the loose side.
Jeez Nibblet you must have been flogging that hard to do that.
@Nibblet I've 2x axle stands you can use if Savage is too far away.
Yeah new spindle about $160 and new CV $60. Will pull the rest of the hub apart and clean it all up at work tonight to see whats salvageable. Will probably have to buy one of those 54mm sockets though, my set only goes to 36mm
Won't say yes, won't so no.
Lets just say if your not airborne your not giving it enough :ORLY:
Should be alright thanks dude. Got a couple of bottle jacks and some tyres sitting under the truck so should be fine.
That's good prices! don't skimp on the cv tho,the factory ones are actually very good,there is also one made Austrailia that is stronger than stock forget the name at the moment.
Just use a hammer and punch don't need a socket.
Get a price for terrain tamer bits, better than toyota. Is Bus and Truck still out the airport way, they used to sell and import the stuff.
I end up fixing so called professionals work after they have used all the proper high end professional tools incorrectly and broken a hardened stud off then un successfully drilled a off center by miles hole with a snapon drill bit that cost four times as much as one that is actually good then they hammer in a brand name screw extractor and snap it in the off center hole with a snapon 18 inch cresent.
Then they are fucked so they bring it to me,And i tell them if you hadn't touched it it would have taken me 2 minutes to remove but now you have butchered it will be an hour or more.:)
Sent from my GT-S5360T using Tapatalk 2
Already all ordered and on the way. Hopefully be up and running again by next weekend.
https://fbcdn-sphotos-d-a.akamaihd.n...7e1f46088586cc
This Pajero came into my mates shop
Not mine thank fuck , Ive got a land cruiser :thumbsup:
was gona say looks like a pajero
Heres the cruiser
https://www.youtube.com/watch?v=f2Gtb5uXC4o
Was rolling a smoke and not watching where I was going ,( seems too be abit of a common occurance ).
And all with the boat still on the back!!!!
Not today Scouser:ORLY: Even closer!
Attachment 28513Attachment 28514Attachment 28515
I wish I was allowed to show photos of our new site:XD:, I have 250mm of clearance on a 180 degree turn with the truck and trailer, miss those marks and shit gets bent.
Just spent the morning helping my son recover his truck and trailer that got stuck over night in the wop wops...all was good till the rain come down...good thing there was a forestry crew close by to help, otherwise it would have been a big hand winch job.
Attachment 29576
Attachment 29577
Attachment 29578
Attachment 29579
Teach him for stealing punga's! :P :D
I can assure you that if he was stealing them, the photos would never have been taken, let alone put on any forum.
While the skidder would certainly do the job would not pretty much any 4wd have done so too?
http://tapatalk.imageshack.com/v2/14...a4f66acd8a.jpg
Shite photo but this geezer tipped his silage trailer over infront of us. Lucky no one was going the other way.
http://tapatalk.imageshack.com/v2/14...a546ad5921.jpg