Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

DPT Delta


User Tag List

+ Reply to Thread
Page 5 of 5 FirstFirst 12345
Results 61 to 70 of 70
Like Tree70Likes

Thread: 7mm RM rechambering

  1. #61
    Member
    Join Date
    Oct 2018
    Location
    Masterton
    Posts
    28
    Quote Originally Posted by Stocky View Post
    Make sure you remember to make sure the thraoting is too suit the shorter tikka magazines. Ask Greg I'm sure he will have specs.
    @Stocky thanks mate yeah will do, have had a good look around and found that there has been two revisions of the CIP standard reamer, Rev B has a freebore measurement of .3645", whereas the original freebore of Rev A was .0631". I’ll confirm what I need with Greg.
    Stocky likes this.

  2. #62
    dog chaser distant stalker's Avatar
    Join Date
    Dec 2011
    Location
    Chch
    Posts
    2,000
    I've read most of the thread and hope.i havent missed this, as the rifle is you should be able to get the 162s to around 3050 fps, with running those numbers how much more are you after from your rifle?

  3. #63
    Member
    Join Date
    Oct 2018
    Location
    Masterton
    Posts
    28
    You’re quite right, the 162gr eldx is great and comfortably gets me to 1000 yards. I ran a ladder test last week, and although the chrono was on the blink it looked like my top accuracy node was only 2920, which isn’t quite there. The goal, and that’s it a goal, would be to have a cartridge/rig capable of 1 mile on steel, and enough energy to take an animal at 1Km. With some great advice, I’m going to work up a load seated out to the lands (a couple possibles I’m working on) and single load to see if it’s worth taking the step up.

  4. #64
    Member
    Join Date
    Apr 2019
    Location
    Wanganui
    Posts
    2,951
    thought about 7mm blaser magnum? mag feed easy in the tikka ditches the belt and performs beauty brass is easy to come by im doing 3060fps 175 eldx less powder than my old RM and quicker

    Quote Originally Posted by Grimus View Post
    OK, so this is a total pipe dream at this stage, but I’m looking at re-chambering my Tikka 7RM. I’m looking at 7-375 Ruger, or possibly 7-300 PRC.
    The thought behind it is, I want to keep it mag feed-able, drop the belt, and increase range.

    First question, can anyone recommend a decent smith for re-chambering? And also dies etc
    Second question, has anyone got these calibres, and what are positives vs negatives of each.

    Thanks in advance for any insights

  5. #65
    Member
    Join Date
    Oct 2018
    Location
    Masterton
    Posts
    28
    Quote Originally Posted by Kelton View Post
    thought about 7mm blaser magnum? mag feed easy in the tikka ditches the belt and performs beauty brass is easy to come by im doing 3060fps 175 eldx less powder than my old RM and quicker
    Yeah, others have suggested 7BM too, and eventually that’s the plan, and absolutely ticks all the boxes

  6. #66
    Member
    Join Date
    Jun 2019
    Location
    Tasman
    Posts
    506
    I would go 7BM ratter that RM if I was to build another too.

  7. #67
    Member
    Join Date
    Oct 2012
    Location
    The UK
    Posts
    107
    Quote Originally Posted by 57jl View Post
    the 8x68s case is a really strong non belted case you could neck down
    The BOO BOO series of cartridges!!!

  8. #68
    Member
    Join Date
    Oct 2018
    Location
    Masterton
    Posts
    28
    Spoke to Tracy at Deadeye, he suggested 7 LRM as a straight rechamber. $350 to rechamber, $200 for dies and $3 a pice for the brass. So for $1000 I could fit the atlasworx DBM and ASICS mags (to run max 3.6” COAL), have the work done and 50 brass. Sounds like a great cartridge, has slightly more capacity than the 7 BM, and a long neck. I understand that the brass wasn't the best, is this still the case? Is there any one out there with this cartridge that can give some real world velocities, and loads?

  9. #69
    Member
    Join Date
    Jun 2019
    Location
    Tasman
    Posts
    506
    IIRC, brass is made by Hornady and is reputed to be poor quality. It’s a good cartridge in theory but has largely failed to gain traction due to poor brass quality.
    Hen likes this.

  10. #70
    Caretaker
    Join Date
    Dec 2011
    Location
    Hawkes Bay
    Posts
    8,757
    Work out which projectile and velocity is required to get the job done

    Make sure your chosen chambering has the best quality brass

    To be effective past 1000yards use the best components made

    Then for the next year be prepared to be schooled by the wind



    Name:  0992917F-969E-4AEC-A3CF-FCD464F2D8FC.jpeg
Views: 202
Size:  4.32 MB
    A big fast bullet beats a little fast bullet every time

 

 

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!