-BW-
Member

484 Likes

Page 13 of 33 First 123456789101112131415161718192021222324252627 ... Last

• Jump to page:

1. 
   Micky Duck liked post by -BW- On thread : How much pitting is too much?

   That reminds me I haven't cleaned my shotgun since last duck season TO-DO list tomorrow: Get beer Clean Shotgun

   Liked On: 27-07-2023, 01:18 PM

2. 
   NAKED_GOOSE liked post by -BW- On thread : How much pitting is too much?

   That reminds me I haven't cleaned my shotgun since last duck season TO-DO list tomorrow: Get beer Clean Shotgun

   Liked On: 27-07-2023, 01:11 PM

3. 
   Jusepy liked post by -BW- On thread : How much pitting is too much?

   That reminds me I haven't cleaned my shotgun since last duck season TO-DO list tomorrow: Get beer Clean Shotgun

   Liked On: 26-07-2023, 09:56 PM

4. 
   techno retard liked post by -BW- On thread : Looking for ideas

   The .244 Rem was Remington's 6mm released in 1955 before Winchester came out with the .243. Skipping over the historical bits, hunters favoured the .243 as it could be bought with 100gr bullets, and...

   Liked On: 26-07-2023, 08:35 AM

5. 
   Trav-6mmrem liked post by -BW- On thread : Looking for ideas

   The .244 Rem was Remington's 6mm released in 1955 before Winchester came out with the .243. Skipping over the historical bits, hunters favoured the .243 as it could be bought with 100gr bullets, and...

   Liked On: 25-07-2023, 11:54 PM

6. 
   Micky Duck liked post by -BW- On thread : Poll: Which calibers to import 1st

   To second the opinion on .312 (because there is a shortage) and lighter 7mm (120-130gr) because there is not much around to choose from.

   Liked On: 24-07-2023, 03:52 PM

7. 
   Micky Duck liked post by -BW- On thread : Poll: Which calibers to import 1st

   Anything goes at the moment. At Nationals the bullet choice is not being scrutinized because everyone understands the lack of supply. I doubt it will ever revert back to the way it was before.

   Liked On: 24-07-2023, 03:51 PM

8. 
   Philipo liked post by -BW- On thread : Who the fuk is "Sam Gibson" ?

   100% It angers me to the core. If the situation wasn't bad enough already.

   Liked On: 23-07-2023, 10:15 PM

9. 
   Micky Duck liked post by -BW- On thread : my 7x60 wildcat project

   Pretty much. the x60 will be a little more capacity than the Ackley but without the benefit of sharper shoulder angle. On the plus side, the x60 doesn't need new dies.

   Liked On: 21-07-2023, 06:12 PM

10. 
    Jaco Goosen liked post by -BW- On thread : my 7x60 wildcat project

    Hi Gents, I thought I would be somewhat greedy and create another wildcat thread, this specifically for the progress of my wildcat mostly from the reloading aspect, as I am currently up to the load...

    Liked On: 21-07-2023, 05:03 PM

11. 
    Micky Duck liked post by -BW- On thread : my 7x60 wildcat project

    Don't know, I don't have any. It could go either way perhaps.

    Liked On: 20-07-2023, 09:09 PM

12. 
    Micky Duck liked post by -BW- On thread : my 7x60 wildcat project

    As far as I understand it (Jaco will know the answer here) The freebore is cut by the reamer, so the reamer would have to be modified in order to shorten the freebore. Mickey Duck is right, extra...

    Liked On: 20-07-2023, 09:06 PM

13. 
    Micky Duck liked post by -BW- On thread : my 7x60 wildcat project

    Now that I have brass, I am moving into loads. 7x57 Sierra 140gr H4350 47.6 Max 2800 fps Speer 130gr H4350 50.0 Max 2930 fps Speer 145gr H4350 50.0 Max 2820 fps ...

    Liked On: 20-07-2023, 08:53 PM

14. 
    SkiHunt liked post by -BW- On thread : my 7x60 wildcat project

    Now that I have brass, I am moving into loads. 7x57 Sierra 140gr H4350 47.6 Max 2800 fps Speer 130gr H4350 50.0 Max 2930 fps Speer 145gr H4350 50.0 Max 2820 fps ...

    Liked On: 20-07-2023, 08:52 PM

15. 
    7mm tragic liked post by -BW- On thread : my 7x60 wildcat project

    Hi Gents, I thought I would be somewhat greedy and create another wildcat thread, this specifically for the progress of my wildcat mostly from the reloading aspect, as I am currently up to the load...

    Liked On: 20-07-2023, 08:43 PM

Page 13 of 33 First 123456789101112131415161718192021222324252627 ... Last

• Jump to page: