-BW-
Member

265 Likes

Page 8 of 18 First 123456789101112131415161718 Last

• Jump to page:

1. 
   -BW- liked post by Wingman On thread : Cutting a die

   I've modified a few dies and found it best to anneal them first espescially if you need to drill or ream them. Heat it up with a propane torch red hot and hold it there for a few mins then drop it...

   Liked On: 29-09-2023, 07:41 PM

2. 
   -BW- liked post by akaroa1 On thread : Cutting a die

   Yes If your reamer is live pilot you can make a custom pilot for a funky bore I recently ground a solid pilot to take live pilots so I could chamber a funky bore It gives more options when...

   Liked On: 29-09-2023, 06:37 PM

3. 
   -BW- liked post by akaroa1 On thread : Cutting a die

   Not so hard I took 10mm off a die recently First cut with a fine cut off wheel Then chucked the die up in my Elliot tool and cutter grinder and faced off the end with the grinder and the die...

   Liked On: 29-09-2023, 06:16 PM

4. 
   -BW- liked post by Fssprecision On thread : Final part of the pistol job

   The final stage in this latest project is now complete, with the manufacture of a suppressor for the little Walther. As is the way, K baffles are the go to for sub sonic situations and in this...

   Liked On: 29-09-2023, 05:37 PM

5. 
   -BW- liked post by XR500 On thread : 7.62x51, and what to do with it.

   Sshhhhh!!!! Actually, I still have a drawer full of receipts for several thousand rounds of MEN85 the army flicked off for no particular reason in the late 1980's. Still have my reloading notebook...

   Liked On: 29-09-2023, 05:26 PM

6. 
   -BW- liked post by Micky Duck On thread : 7mm08 barrel shortening

   first ever hunt........ DONT change stuff till youve used it enough to decide if you need to...or you will be chasing your tail and flushing good coin down the drain

   Liked On: 29-09-2023, 08:31 AM

7. 
   -BW- liked post by Von Gruff Knives On thread : A Lee Speed stock

   Was able to get back to this today and got the mag well sorted for a nice slide fit for both 10 and 5 shot mags https://i.imgur.com/nglElZml.jpg After that was done I did the reinforce across...

   Liked On: 28-09-2023, 12:05 PM

8. 
   -BW- liked post by Von Gruff Knives On thread : A Lee Speed stock

   This morning saw the trigger guard settled into place and then the magazine cut off plate was also fitted with the appropriate wood removed to allow it to operate. Slow and methodical with a great...

   Liked On: 28-09-2023, 12:04 PM

9. 
   -BW- liked post by Von Gruff Knives On thread : A Lee Speed stock

   With the B/A tight into the inlet the unit can be turned over in the vise and the TG sat in between the fixing ears and lined up with the center mark on the underside of the fore stock and fine...

   Liked On: 28-09-2023, 12:04 PM

10. 
    -BW- liked post by Von Gruff Knives On thread : A Lee Speed stock

    With the spare action inlet down to depth it was time to sit the actual B/A in the wood as far as it would go and mark the barrel channel then start the inlet with a wide flat chisel ...

    Liked On: 28-09-2023, 12:04 PM

11. 
    -BW- liked post by akaroa1 On thread : Wildcat appreciation thread

    I tweaked the die length this morning to make the neck slightly longer This 9.5x62R case is remarkably similar to the 303 Brit Will feed and extract like a dream 228259

    Liked On: 23-09-2023, 04:21 PM

12. 
    -BW- liked post by EmpireSafaris On thread : Greener in the Field

    https://i.postimg.cc/LsxvFGrD/2908C116-71ED-46D9-B2DC-26466CB1D6B3.jpg (https://postimg.cc/qtC28DB6) https://i.postimg.cc/nL3sd2B6/5CC6ED1B-7688-4CEB-8BDE-E9A82DB165A6.jpg ...

    Liked On: 20-09-2023, 11:03 PM

13. 
    -BW- liked post by Blackfern On thread : Mixed Headstamp brass in 270 - performance differences

    PPU is a bit of a hidden gem if you ask me. Super consistent weights and size. And being perceived as uncool people will pretty much give you once fired brass. Can't see the point of paying 300...

    Liked On: 15-09-2023, 04:44 PM

14. 
    -BW- liked post by Hunter_Nick On thread : Walnut and blued steel,

    Picked up my final project from Alden Carr this morning, my long awaited ‘Remchester’ .358 Win. Metalwork was done by him, with the stock built and checkered by myself. Douglas premium barrel #3...

    Liked On: 12-09-2023, 05:45 PM

15. 
    -BW- liked post by rambo-6mmrem On thread : Walnut and blued steel,

    A couple of recent add on’s to the collection 1st up my rolling block 40-65 I have wanted a 40-65 for a fair while (45-70 necked down to.408) To add to the collection of long range black powder...

    Liked On: 12-09-2023, 05:44 PM

Page 8 of 18 First 123456789101112131415161718 Last

• Jump to page: