About 300_BLK

Basic Information


Age
39
About 300_BLK
Location:
NZ

Signature


Warm Barrels!

Statistics


Total Posts
Total Posts
3,619
Posts Per Day
1.01
General Information
Last Activity
Yesterday 07:06 PM
Join Date
14-08-2014
Referrals
1

7 Friends

  1. camo wsm camo wsm is offline

    Member

    camo wsm
  2. Cowboy06 Cowboy06 is offline

    Member

    Cowboy06
  3. Gun nut Gun nut is offline

    Member

    Gun nut
  4. Kaiser Metz Kaiser Metz is offline

    Gone but not forgotten

    Kaiser Metz
  5. mawzer308 mawzer308 is offline

    Member

    mawzer308
  6. Uplandstalker Uplandstalker is offline

    Member

    Uplandstalker
  7. Wurzelmangler Wurzelmangler is offline

    Member

    Wurzelmangler
Showing Friends 1 to 7 of 7

1052 Likes

  1. gadgetman
    gadgetman liked post by 300_BLK On thread : Tell me about carbon wrapped barrels
    @gagetman I believe the tests were done in a paint oven where each barrel was kept at a consistent temp based on research done with a laser thermometer after shooting steel and carbon barrels. It...
    Liked On: 13-11-2017, 09:00 AM
  2. PERRISCICABA
    PERRISCICABA liked post by 300_BLK On thread : Torn between two lo....
    Go full retard then and do a 22-243AI! 90 bergers over 3100
    Liked On: 13-11-2017, 07:52 AM
  3. Micky Duck
    Micky Duck liked post by 300_BLK On thread : How short on a 303?
    Thanks Micky Duck I have some 212 gr lead round nose, dies and brass. I’ll cut her to 16” and throw the Ase Utra can on
    Liked On: 12-11-2017, 09:28 PM
  4. Echo
    Echo liked post by 300_BLK On thread : Tell me about carbon wrapped barrels
    Local gunsmith did some testing here recently. Measured stiffness with carbon and equivalent weight carbon barrels and found they are identical. For example my 24” proof research is a sender...
    Liked On: 12-11-2017, 09:26 PM
  5. BRADS
    BRADS liked post by 300_BLK On thread : Tell me about carbon wrapped barrels
    Local gunsmith did some testing here recently. Measured stiffness with carbon and equivalent weight carbon barrels and found they are identical. For example my 24” proof research is a sender...
    Liked On: 12-11-2017, 09:10 PM
  6. Double Shot
    Double Shot liked post by 300_BLK On thread : Torn between two lo....
    If you go 22-243 win PM me. I have data for a slow twist barrel and some brass you can have.
    Liked On: 12-11-2017, 11:10 AM
  7. matto1234
    matto1234 liked post by 300_BLK On thread : Torn between two lo....
    Go full retard then and do a 22-243AI! 90 bergers over 3100
    Liked On: 11-11-2017, 08:31 PM
  8. Double Shot
    Double Shot liked post by 300_BLK On thread : Torn between two lo....
    Go full retard then and do a 22-243AI! 90 bergers over 3100
    Liked On: 11-11-2017, 07:08 PM
  9. Cordite
    Cordite liked post by 300_BLK On thread : Is "light pitting" really bad
    If it still shoots well then no
    Liked On: 11-11-2017, 06:39 PM
  10. 223nut
    223nut liked post by 300_BLK On thread : Couriering a rifle
    Nz couriers will send without the fuss to an address. Breath of fresh air, a lot cheaper too. $36 overnight between islands
    Liked On: 08-11-2017, 08:56 AM
  11. Marty Henry
    Marty Henry liked post by 300_BLK On thread : How short on a 303?
    Don't worry it is an older PH Supreme model that I picked up for $150 not a minter
    Liked On: 07-11-2017, 10:54 AM
  12. Boaraxa
    Boaraxa liked post by 300_BLK On thread : Wicked evening
    Well done mate, hooked for life!
    Liked On: 29-10-2017, 09:58 PM
  13. Tahr
    Tahr liked post by 300_BLK On thread : Ouch!
    Nice! Nothing more satisfying than bringing home some venni, especially when you don’t waste much !!
    Liked On: 29-10-2017, 06:07 PM
  14. tetawa
    tetawa liked post by 300_BLK On thread : Dud Hornady Die?
    Hey LOC I have a few sets of hornady and encountered your problem. Best way to avoid it is to strip the die when you get them and then clean them before reassembling them with a bit of case live on...
    Liked On: 23-10-2017, 10:05 AM
  15. LOC
    LOC liked post by 300_BLK On thread : Dud Hornady Die?
    Hey LOC I have a few sets of hornady and encountered your problem. Best way to avoid it is to strip the die when you get them and then clean them before reassembling them with a bit of case live on...
    Liked On: 23-10-2017, 08:11 AM

02-07-2015



No results to display...
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!