7mmsaum
Caretaker

5771 Likes

Page 87 of 385 First ... 37737475767778798081828384858687888990919293949596979899100101137187 ... Last

• Jump to page:

1. 
   7mmsaum liked post by Big_Bear On thread : New To This

   Hi everyone, I am new to the forum but am loving this community so far! I am just getting started hunting with a 7mm-08. I look forward to being a part of what is happening here.

   Liked On: 29-01-2023, 07:29 PM

2. 
   7mmsaum liked post by stagstalker On thread : Rifle Bedding Opinions

   55 and 65 inch pounds seems like a lot. I could be wrong but on my plastic Tikka stocks I torque to 35 inch pounds to avoid any unnecessary compression and on my carbon stocks with pillars I go 40...

   Liked On: 27-01-2023, 08:45 PM

3. 
   7mmsaum liked post by viper On thread : What breed of deer are these ?

   :D , classic. Goes to Bali, lovely beach's, ton of bars and restaurants. Warm sea , culture but "NO" , in typical NZHS member behavior Nathan F is in the bush stalking fucking deer.

   Liked On: 23-01-2023, 03:38 PM

4. 
   7mmsaum liked post by Pommy On thread : CFE223 & 55 grain .223

   I'd say it's a bit too slow. Iirc, it's a tad slower than 2208. In my experience, the slow for calibre ball powders with light bullets burn like coal (which isn't great for consistency or accuracy)...

   Liked On: 20-01-2023, 02:38 AM

5. 
   7mmsaum liked post by Fssprecision On thread : When you can't get the parts

   Well sometimes you can't get old parts so you just have to make it from stock. This old Tikka had the bolt release missing and no parts were available so a few hours milling later and all working...

   Liked On: 17-01-2023, 06:15 PM

6. 
   7mmsaum liked post by Trout On thread : Should I have shot this Deer?

   Its a deer,shoot it and fill your freezer.

   Liked On: 16-01-2023, 10:28 PM

7. 
   7mmsaum liked post by Nathan F On thread : Should I have shot this Deer?

   What are you even asking. Knock them over. Take the meat.

   Liked On: 16-01-2023, 10:28 PM

8. 
   7mmsaum liked post by Tahr On thread : Old Farts...

   Out and about. Some pics (and something for stug to look at to help with the boredom). This was a good omen. 214582 I shot this at 340 yards with the 6.5x55. It was trying to make good its...

   Liked On: 15-01-2023, 02:50 PM

9. 
   7mmsaum liked post by norsk On thread : Suppressor Cleaning.

   It cleans them up bright and shiney! Did that to an A-tec and all the anodizing came off. Made it very clean however.

   Liked On: 15-01-2023, 08:01 AM

10. 
    7mmsaum liked post by ShortStuff On thread : Walkabout

    So went for my first walkabout for 2023 yesterday. Goal for the day was to try and find a clearing I had been told about. Up I was at zero dark thirty like most trips and quick stop at the local...

    Liked On: 14-01-2023, 05:25 PM

11. 
    7mmsaum liked post by Micky Duck On thread : Stihl chainsaw choice

    photo needed....

    Liked On: 14-01-2023, 01:05 PM

12. 
    7mmsaum liked post by Ingrid 51 On thread : Stihl chainsaw choice

    Thanks to everyone for their input. A mate has GIVEN me a Stihl 211. That will do for the trimming and a couple of fellings, before being cleaned and stored for next season. I appreciate that battery...

    Liked On: 14-01-2023, 08:06 AM

13. 
    7mmsaum liked post by Plinky On thread : Rem 700 help

    Carbon ring build up like Husky 1600 has suggested, had the same issue a couple of times.

    Liked On: 12-01-2023, 11:27 AM

14. 
    7mmsaum liked post by Husky1600 On thread : Rem 700 help

    I've heard of a number of cases lately that was tracked down to a carbon build up not too far forward of the chamber. Takes a bit of moving, with the right products. Apparently some powders are more...

    Liked On: 12-01-2023, 11:27 AM

15. 
    7mmsaum liked post by Ryan_Songhurst On thread : First deer

    Dinner dinner dinner dinner, batman

    Liked On: 12-01-2023, 07:23 AM

Page 87 of 385 First ... 37737475767778798081828384858687888990919293949596979899100101137187 ... Last

• Jump to page: