7mmsaum
Caretaker

5207 Likes

Page 21 of 348 First ... 789101112131415161718192021222324252627282930313233343571121 ... Last

• Jump to page:

1. 
   7mmsaum liked post by Micky Duck On thread : 223 on deer

   fired single 55grn sierra softpoint today (loads given to me by 257 weatherby years ago LOL) it tipped over nice fat fallow spiker/stag at 150ish..he went all of 20 yards with tip of heart missing...

   Liked On: 14-11-2023, 03:59 PM

2. 
   7mmsaum liked post by Nakihunter On thread : New Tikka T3X Aspire - enjoying it

   I bought a Tikka T3x Superlite Aspite about 8 weeks ago. I just couldn't resist the rifle when I saw it in Whakatane Hunting & fishing. Alan did a package deal with a basic Burris 3-9X scope. I...

   Liked On: 13-11-2023, 06:03 PM

3. 
   7mmsaum liked post by Tentman On thread : Best chainsaw.

   Haha - entirely mission dependent . . . . I've had a crew building a track on Stewart Is for the last week. They had my little battery MSA200. It was constantly in use, build a set of steps here,...

   Liked On: 12-11-2023, 07:24 PM

4. 
   7mmsaum liked post by timattalon On thread : Timattalon's MX5 woes

   Theres a couple of motors I have had in the past that I would think woould be very fun in the wee car... 1st is the 1.8l V6 out of the Mazda Presso which is a FWD coupe version of the RWD MX5 . It...

   Liked On: 12-11-2023, 04:33 PM

5. 
   7mmsaum liked post by stumpys On thread : Found knife

   Someone missing a knife? Found deep in the Pureora, tell me where and I'll get it back to you.237367

   Liked On: 12-11-2023, 03:21 PM

6. 
   7mmsaum liked post by Bill999 On thread : Timattalon's MX5 woes

   aparently 13b's bolt right to the gearboxes how are things at the salon these days?

   Liked On: 12-11-2023, 02:12 PM

7. 
   7mmsaum liked post by Grey Kiwi On thread : Timattalon's MX5 woes

   Tim...try a new key with Loctite 660. Give that crank end a good clean up first. This stuff is made for this sort of problem. If nothing else, it will save you from having to rush into a motor...

   Liked On: 12-11-2023, 02:09 PM

8. 
   7mmsaum liked post by ebf On thread : Best chainsaw.

   When you say guides, do you mean the rakers, the part of the chain that determines how much of the tooth is engaged ? If that is what you are gringing down, and boring with the tip, you might want...

   Liked On: 12-11-2023, 01:48 PM

9. 
   7mmsaum liked post by Shearer On thread : 223 on deer

   Went to the range yesterday to verify zero after making a new batch of ammo neck sizing only. No problems there. 237364 Took the 223 out that evening for a proper field test. No problem there...

   Liked On: 12-11-2023, 01:31 PM

10. 
    7mmsaum liked post by FosterOsinski On thread : Newbie

    Nice gun:cool:

    Liked On: 12-11-2023, 08:52 AM

11. 
    7mmsaum liked post by bigbear On thread : Easy hunt with the 308

    After a write up by Kelton he got me aspired to take the 308 for a walk. A quick 25minute drive and seeing a couple of road side deer keeps one’s hopes high at first light. Chuck a bit of gear on...

    Liked On: 12-11-2023, 07:38 AM

12. 
    7mmsaum liked post by Kelton On thread : Sambar Calibre

    Shit I must tell the samber bones iv shot their not dead because I only used a 16” .308, .270 deals to them to but yes big and strong if it’s a dedicated samber shooter hack a 300wsm down long shots...

    Liked On: 10-11-2023, 09:19 PM

13. 
    7mmsaum liked post by Tahr On thread : Gun Porn, show off your new toys

    That will make it a lot easier to sell :)

    Liked On: 10-11-2023, 09:12 PM

14. 
    7mmsaum liked post by Rees On thread : Sambar Calibre

    its the projectile that needs to be of standard, not the Calibre.......... period.

    Liked On: 10-11-2023, 08:31 PM

15. 
    7mmsaum liked post by Missalot On thread : Newbie

    Hi everyone, Long time listener first time caller. Farmer from north otago, keen on anything that goes bang. Weapons of choice are Sako 85 varmint 22-250 + nightforce shv & Waitaki engineering...

    Liked On: 08-11-2023, 06:00 PM

Page 21 of 348 First ... 789101112131415161718192021222324252627282930313233343571121 ... Last

• Jump to page: