akaroa1
Member

5230 Likes

Page 65 of 349 First ... 155152535455565758596061626364656667686970717273747576777879115165 ... Last

• Jump to page:

1. 
   Roarless20 liked post by akaroa1 On thread : Tips on reaming a chamber

   Well I would hand cut it with the barrel muzzle down in a vice with protected jaws, Relatively small tap holder as your driver Take the live pilot off the reamer and check that it will slide...

   Liked On: 18-09-2023, 07:56 PM

2. 
   T.FOYE liked post by akaroa1 On thread : Cast Lead Thread ?

   And here's a good tip for bullet casters I mainly powder coat my bullets and use pass through sizers Haven't used my Lyman lube sizer in a few years So I made these dies bodies to take the...

   Liked On: 17-09-2023, 08:32 PM

3. 
   Moa Hunter liked post by akaroa1 On thread : Cast Lead Thread ?

   And here's a good tip for bullet casters I mainly powder coat my bullets and use pass through sizers Haven't used my Lyman lube sizer in a few years So I made these dies bodies to take the...

   Liked On: 16-09-2023, 12:57 AM

4. 
   Micky Duck liked post by akaroa1 On thread : Cast Lead Thread ?

   And here's a good tip for bullet casters I mainly powder coat my bullets and use pass through sizers Haven't used my Lyman lube sizer in a few years So I made these dies bodies to take the...

   Liked On: 15-09-2023, 10:11 PM

5. 
   Micky Duck liked post by akaroa1 On thread : Cast Lead Thread ?

   I've been doing a lot of casting and powder coating lately Belted Balls for the Dickson 233231 Three different flavour of bullets for the 32-20 233233

   Liked On: 15-09-2023, 09:30 PM

6. 
   Moa Hunter liked post by akaroa1 On thread : Cast Lead Thread ?

   I've been doing a lot of casting and powder coating lately Belted Balls for the Dickson 233231 Three different flavour of bullets for the 32-20 233233

   Liked On: 15-09-2023, 09:31 AM

7. 
   T.FOYE liked post by akaroa1 On thread : Cast Lead Thread ?

   Eastwood from Resto Supplies in Auckland

   Liked On: 15-09-2023, 07:15 AM

8. 
   kristopher liked post by akaroa1 On thread : Tips on reaming a chamber

   Well I would hand cut it with the barrel muzzle down in a vice with protected jaws, Relatively small tap holder as your driver Take the live pilot off the reamer and check that it will slide...

   Liked On: 14-09-2023, 05:33 PM

9. 
   blip liked post by akaroa1 On thread : Tips on reaming a chamber

   I re cut a 223 Howa new old stock barrel a couple of weeks ago to 222 Rimmed The barrel was being stubbed into a Contender barrel shank and I was able to set it back a little I have cut quite a few...

   Liked On: 13-09-2023, 10:16 PM

10. 
    blip liked post by akaroa1 On thread : Tips on reaming a chamber

    Well I would hand cut it with the barrel muzzle down in a vice with protected jaws, Relatively small tap holder as your driver Take the live pilot off the reamer and check that it will slide...

    Liked On: 13-09-2023, 10:15 PM

11. 
    Micky Duck liked post by akaroa1 On thread : Tips on reaming a chamber

    I re cut a 223 Howa new old stock barrel a couple of weeks ago to 222 Rimmed The barrel was being stubbed into a Contender barrel shank and I was able to set it back a little I have cut quite a few...

    Liked On: 13-09-2023, 08:47 PM

12. 
    Micky Duck liked post by akaroa1 On thread : Tips on reaming a chamber

    Well I would hand cut it with the barrel muzzle down in a vice with protected jaws, Relatively small tap holder as your driver Take the live pilot off the reamer and check that it will slide...

    Liked On: 13-09-2023, 08:47 PM

13. 
    zimmer liked post by akaroa1 On thread : Tips on reaming a chamber

    Well I would hand cut it with the barrel muzzle down in a vice with protected jaws, Relatively small tap holder as your driver Take the live pilot off the reamer and check that it will slide...

    Liked On: 13-09-2023, 08:41 PM

14. 
    Micky Duck liked post by akaroa1 On thread : Walnut and blued steel,

    All the walnut I have on hand here in Akaroa similarly comes from trees planted by the original settlers circa 1850 Most of those original trees just start dying of old age at around 150 years old ...

    Liked On: 12-09-2023, 07:29 PM

15. 
    Micky Duck liked post by akaroa1 On thread : Useing the firearms register

    Yes the really big hoards are yet too come And they will mostly be ring in and do them one at a time because they aren't cookie cutter guns Recently talked to a guy helping out a friend and...

    Liked On: 12-09-2023, 03:39 PM

Page 65 of 349 First ... 155152535455565758596061626364656667686970717273747576777879115165 ... Last

• Jump to page: