Basenjiboy
Member

131 Likes

Page 8 of 9 First 123456789 Last

• Jump to page:

1. 
   Waynesworld liked post by Basenjiboy On thread : advice on .222 loads

   I run a sako L461 and don't have any problems with 55 grain Hornadys. I'm using AR2207 rather than 2208.

   Liked On: 23-07-2020, 07:56 PM

2. 
   timattalon liked post by Basenjiboy On thread : 7.62x39 hollow point projectiles?

   Try Barnaul.co.nz They had the 123 grain hollow points last time i ordered. (Jim is real easy to deal with, and good prices)

   Liked On: 22-06-2020, 11:21 PM

3. 
   Finnwolf liked post by Basenjiboy On thread : 7.62x39 hollow point projectiles?

   Try Barnaul.co.nz They had the 123 grain hollow points last time i ordered. (Jim is real easy to deal with, and good prices)

   Liked On: 22-06-2020, 08:05 PM

4. 
   mimms2 liked post by Basenjiboy On thread : Getting ahead of new range rules

   I've been personally involved in range certification for many years. The NZ firearms range manual is here: https://www.police.govt.nz/about-us/publication/new-zealand-police-firearms-range-manual...

   Liked On: 22-06-2020, 05:20 PM

5. 
   Moa Hunter liked post by Basenjiboy On thread : Getting ahead of new range rules

   I've been personally involved in range certification for many years. The NZ firearms range manual is here: https://www.police.govt.nz/about-us/publication/new-zealand-police-firearms-range-manual...

   Liked On: 20-06-2020, 03:46 PM

6. 
   timattalon liked post by Basenjiboy On thread : Tahr cull to resume

   Yes, and all the talk about recreational shooters being involved is bulldust! NZDA asked at one of their consultation meetings about them wanting our tallies -apparently not only have they not done...

   Liked On: 01-06-2020, 11:07 PM

7. 
   outdoorlad liked post by Basenjiboy On thread : Tahr cull to resume

   Yes, and all the talk about recreational shooters being involved is bulldust! NZDA asked at one of their consultation meetings about them wanting our tallies -apparently not only have they not done...

   Liked On: 01-06-2020, 01:25 PM

8. 
   ANOTHERHUNTER liked post by Basenjiboy On thread : 80s series build

   Cut down the inner from a IBC, fits nicely between the wheel arches -can be as deep as you want, but normally 300mm is about right. 140894

   Liked On: 31-05-2020, 12:09 PM

9. 
   csmiffy liked post by Basenjiboy On thread : 80s series build

   Cut down the inner from a IBC, fits nicely between the wheel arches -can be as deep as you want, but normally 300mm is about right. 140894

   Liked On: 28-05-2020, 02:30 PM

10. 
    Husky1600 liked post by Basenjiboy On thread : 80s series build

    Cut down the inner from a IBC, fits nicely between the wheel arches -can be as deep as you want, but normally 300mm is about right. 140894

    Liked On: 26-05-2020, 10:35 PM

11. 
    mimms2 liked post by Basenjiboy On thread : 80s series build

    Cut down the inner from a IBC, fits nicely between the wheel arches -can be as deep as you want, but normally 300mm is about right. 140894

    Liked On: 26-05-2020, 10:03 PM

12. 
    Brian liked post by Basenjiboy On thread : 80s series build

    Cut down the inner from a IBC, fits nicely between the wheel arches -can be as deep as you want, but normally 300mm is about right. 140894

    Liked On: 26-05-2020, 09:22 PM

13. 
    223nut liked post by Basenjiboy On thread : 80s series build

    Cut down the inner from a IBC, fits nicely between the wheel arches -can be as deep as you want, but normally 300mm is about right. 140894

    Liked On: 26-05-2020, 09:05 PM

14. 
    sometimes1 liked post by Basenjiboy On thread : 80s series build

    Cut down the inner from a IBC, fits nicely between the wheel arches -can be as deep as you want, but normally 300mm is about right. 140894

    Liked On: 26-05-2020, 08:09 PM

15. 
    northdude liked post by Basenjiboy On thread : Vixen optics

    I've got a Vixen in 3-12x40. It replaced an old leupold Vari-X II; far far better in low light, and more usable field of veiw to the edges. BB.

    Liked On: 10-05-2020, 10:46 AM

Page 8 of 9 First 123456789 Last

• Jump to page: