Beaker
Member

11004 Likes

Page 574 of 734 First ... 74474524560561562563564565566567568569570571572573574575576577578579580581582583584585586587588624674 ... Last

• Jump to page:

1. 
   Beaker liked post by zimmer On thread : Smallbore shooting

   WallyR - dead right about position and treating each shot as an individual (plus excluding from your brain the value of the last shot if it was a bummer). Once I was shooting reasonably well I used...

   Liked On: 26-07-2016, 06:04 PM

2. 
   Beaker liked post by R93 On thread : Slow shooting.

   July. Awesome day for a change here on the coast. Cleaned my barrel with solvent and bronze brush. Run some patches till they come out clean and headed up the range with my kestrel in my range...

   Liked On: 26-07-2016, 06:01 PM

3. 
   Beaker liked post by WallyR On thread : Smallbore shooting

   Don't worry young fella. Moving your point of aim to a new target every shot, takes a little getting used to. When I started (with a 10X fixed power ex-Army scope), I really had to focus on each...

   Liked On: 26-07-2016, 05:57 PM

4. 
   Beaker liked post by homebrew.357 On thread : Makeing a double paper patch mould

   I just put in three pins, :huh: , more the merrier, but it works, and no boring bar, I made up a "D" bit from sliver steel the shape of the bullet. I`m using handles and spruce cutter for another...

   Liked On: 25-07-2016, 08:51 PM

5. 
   Beaker liked post by Rushy On thread : Dinner thread?

   Just whipped up some meatballs for a Spaghetti and ...... Home grown home kill beef mince. I may have overdone the garlic but then part of me says that isn't possible. 52784

   Liked On: 25-07-2016, 07:33 PM

6. 
   Beaker liked post by Frogfeatures On thread : Beam scales vs Electronic

   Slightly off topic, but I anneal my cases after every 4th firing. Between cleaning primer pockets, annealing, and being anal, I THINK it gives me better results. Anyway, I'm happy, I'd rather over...

   Liked On: 25-07-2016, 05:22 PM

7. 
   Beaker liked post by viper On thread : Beam scales vs Electronic

   Yeah your right FrogFeatures, I hated reloading the first time I started but his time round my head is in a different space and I just cruise out and slowly work through it . Measure every load so...

   Liked On: 25-07-2016, 05:22 PM

8. 
   Beaker liked post by grunzter On thread : Tell 'em they're dreaming . . . Govt announces new policy, predator free by 2050

   Carpet bombing with 1080... 52776

   Liked On: 25-07-2016, 05:13 PM

9. 
   Beaker liked post by Pengy On thread : 2016 Toby Goodley Memorial shoot in Central Hawkes Bay

   Best first post ever. Welcome aboard. :thumbsup:

   Liked On: 24-07-2016, 11:41 PM

10. 
    Beaker liked post by Rushy On thread : 2016 Toby Goodley Memorial shoot in Central Hawkes Bay

    Make a quick trip back for it Blaser. Sorted

    Liked On: 24-07-2016, 11:41 PM

11. 
    Beaker liked post by Simon On thread : AR15 Federal Primers

    Must be a faulty primer with that dent in it. I use cci small rifle primers #400. Probably used 100K plus through pistols and 40-50K through rifles. I cannot remember ever having one not going off.

    Liked On: 24-07-2016, 11:22 PM

12. 
    Beaker liked post by R93 On thread : Gun Porn, show off your new toys

    Challenge accepted. And I still have a shadow but doubt I will need to dirty it😆 Sent from my SM-G900F using Tapatalk

    Liked On: 24-07-2016, 11:16 PM

13. 
    Beaker liked post by R93 On thread : Gun Porn, show off your new toys

    No you wouldnt. Not unless you used a glock with a fag mag😆 18+1 in the M40 Sent from my SM-G900F using Tapatalk

    Liked On: 24-07-2016, 11:02 PM

14. 
    Beaker liked post by Pointer On thread : Holland and Holland

    Dollimore is the man. He is Purdey trained so may turn his nose up at a lowly H&H :D Don't forget to post pics on here though...

    Liked On: 24-07-2016, 10:41 PM

15. 
    Beaker liked post by homebrew.357 On thread : Makeing a double paper patch mould

    Ok, now the next bit is to machine two of the ali blocks faces true, again set up in chuck and skim one face on each block. Now the two faces will be the inside of the mould but before drilling the...

    Liked On: 24-07-2016, 10:38 PM

Page 574 of 734 First ... 74474524560561562563564565566567568569570571572573574575576577578579580581582583584585586587588624674 ... Last

• Jump to page: