Bill999
Member

2149 Likes

Page 17 of 144 First ... 34567891011121314151617181920212223242526272829303167117 ... Last

• Jump to page:

1. 
   Bill999 liked post by gundoc On thread : Tips on reaming a chamber

   I use a floating holder and ream chambers in the lathe to about 90% depth, taking great care to ensure bore is perfectly true before starting. I also drill a pilot hole first (about 75% of the...

   Liked On: 14-09-2023, 09:40 AM

2. 
   Bill999 liked post by Hunter_Nick On thread : JW15 trigger overtravel

   This has got to be the single best thing I’ve done to my JW15. It’s a great little rifle and quite accurate, but the 4 miles of overtravel in the trigger has always annoyed me. Just didn’t feel like...

   Liked On: 14-09-2023, 09:36 AM

3. 
   Bill999 liked post by Dan88 On thread : Gunsmith Lower North Island

   Mr Max in lower hutt knows what he is doing, threaded my .300wsm and .22-250 easy as

   Liked On: 14-09-2023, 09:27 AM

4. 
   Bill999 liked post by Rock river arms hunter On thread : 308 barrel length velocity loss

   Yep. Not suprised by the numbers. Sounds like my 308 will be heading off for a barrel chop, half cock installed. Cheers team!

   Liked On: 12-09-2023, 08:51 AM

5. 
   Bill999 liked post by Flyblown On thread : 308 subsonic

   It’s a common response and fair enough really. Here’s some thoughts. Firstly, fallow and goats aren’t big game. They’re on the small end of medium game. That’s a nitpick but relevant. We’re not...

   Liked On: 09-09-2023, 10:31 AM

6. 
   Bill999 liked post by Flyblown On thread : 308 subsonic

   https://www.nzhuntingandshooting.co.nz/f17/subsonic-action-63970/ An old 308 subsonic thread I’ve posted a few years ago. Robert’s cast lead 151gr pills. (@shooternz) I’ve got photos of some of...

   Liked On: 09-09-2023, 10:29 AM

7. 
   Bill999 liked post by Flyblown On thread : 308 subsonic

   I pulled this one out of a fallow spiker shot quartering strongly towards, through the base of the neck and into the spine, deflected down and through the lungs. Found it in the cavity around the...

   Liked On: 09-09-2023, 10:27 AM

8. 
   Bill999 liked post by StrikerNZ On thread : JARD .17 WSM Reliability Issues

   Sounds like about time to insist on a refund. Clearly some form of fault in the rifle, not really reasonable to expect you to put up with the misfires and replacing firing pins every 3 months.

   Liked On: 29-08-2023, 04:27 PM

9. 
   Bill999 liked post by Frogfeatures On thread : DPT mk 2 performance?

   I have both, not quite sure how it happened, ( in the same calibre :wtfsmilie: ) but anyway….. I can’t tell the difference between the 2 Just keep using the 308.

   Liked On: 28-08-2023, 10:11 AM

10. 
    Bill999 liked post by Shearer On thread : First attempt at reloading. Thoughts please.

    I assume you weren't getting any pressure signs even at 42.5gns? I would usually work up until things started looking hot and then look back from there.

    Liked On: 23-08-2023, 10:20 AM

11. 
    Bill999 liked post by Micky Duck On thread : Knife sharpeners you’d recommend

    Slighty off topic.......if anyone local to here,or going past needs knives sharpened...flick me a PM and I will sort them for you...that includes the long neglected knives from the kitchen too,good...

    Liked On: 22-08-2023, 03:05 PM

12. 
    Bill999 liked post by NRT On thread : Photos of your dog

    228732 Jager six months old ,a right handful.

    Liked On: 22-08-2023, 09:23 AM

13. 
    Bill999 liked post by feratox On thread : Ruger 10/22 wont cycle

    If you're careful, try lapping the bolt to the raceways so its as smooth as it can get. Also "smoothing" or putting a gentle radius on the lower rear of the bolt to help it ride over the hammer...

    Liked On: 22-08-2023, 08:50 AM

14. 
    Bill999 liked post by garyp On thread : Help in Auckland required. Snapped scope ring bolt

    Get a little tiny sharp screwdriver and tap one side of the stubb to turn it out. Put a drop of penetrating oil or acetone ( nail polish remover) on it and leave it a few minutes before trying.

    Liked On: 22-08-2023, 08:47 AM

15. 
    Bill999 liked post by Puffin On thread : Identify that Knife Sharpener

    There are a lot of knife sharpening systems out there. Here is a compilation of most of them that have been mentioned on here over the past eight years - to help make them easier to identify by name...

    Liked On: 21-08-2023, 02:43 PM

Page 17 of 144 First ... 34567891011121314151617181920212223242526272829303167117 ... Last

• Jump to page: