Brian
Member

947 Likes

Page 11 of 64 First 1234567891011121314151617181920212223242561 ... Last

• Jump to page:

1. 
   RUMPY liked post by Brian On thread : Using hard items as rests

   Use my pack frame a lot and it doesn't seem to matter that its hard. When your out in the steep tussock any rest is a good one.

   Liked On: 02-10-2023, 02:29 PM

2. 
   chainsaw liked post by Brian On thread : Using hard items as rests

   Use my pack frame a lot and it doesn't seem to matter that its hard. When your out in the steep tussock any rest is a good one.

   Liked On: 02-10-2023, 02:27 PM

3. 
   csmiffy liked post by Brian On thread : Pressure point bedding parker hale

   I make a pillar for the rear screw and epoxy that in before bedding the front of the action. You need a clearance on the rear of the tang too.

   Liked On: 29-07-2023, 06:07 PM

4. 
   No.3 liked post by Brian On thread : Pressure point bedding parker hale

   I make a pillar for the rear screw and epoxy that in before bedding the front of the action. You need a clearance on the rear of the tang too.

   Liked On: 25-07-2023, 11:54 PM

5. 
   Micky Duck liked post by Brian On thread : Pressure point bedding parker hale

   I make a pillar for the rear screw and epoxy that in before bedding the front of the action. You need a clearance on the rear of the tang too.

   Liked On: 25-07-2023, 08:47 PM

6. 
   Moa Hunter liked post by Brian On thread : my 7x60 wildcat project

   I took the handle off a case trimmer and put a battery drill on it. Takes 2-3mm off in no time. The dimpled cases will come out perfect after firing them as long as you can chamber them.

   Liked On: 21-07-2023, 08:54 AM

7. 
   nor-west liked post by Brian On thread : my 7x60 wildcat project

   I took the handle off a case trimmer and put a battery drill on it. Takes 2-3mm off in no time. The dimpled cases will come out perfect after firing them as long as you can chamber them.

   Liked On: 20-07-2023, 10:10 PM

8. 
   Micky Duck liked post by Brian On thread : my 7x60 wildcat project

   I took the handle off a case trimmer and put a battery drill on it. Takes 2-3mm off in no time. The dimpled cases will come out perfect after firing them as long as you can chamber them.

   Liked On: 20-07-2023, 09:33 PM

9. 
   Micky Duck liked post by Brian On thread : Mahogany for rifle stock?

   I've got one a mate made for me 55years ago. A bit heavier but stable and strong. Never had any problems with it.

   Liked On: 20-07-2023, 05:55 PM

10. 
    Micky Duck liked post by Brian On thread : Your cartridge of choice.

    If I wrote a list of all my guns I'd probably frighten myself and find some I'd forgotten but a 7x33 sako is the most unusual.

    Liked On: 19-07-2023, 05:08 PM

11. 
    FRST liked post by Brian On thread : Oberndorf Mauser

    Like it. An old rifle should look like its had a bit of use.

    Liked On: 18-07-2023, 10:48 AM

12. 
    Synthetic liked post by Brian On thread : Lever guns - What do ya reckon?

    If you change from a bolt to a lever or semi you need to retrain your instinctive shooting or you will fire one shot and grab for the bolt handle.

    Liked On: 17-07-2023, 11:46 PM

13. 
    Micky Duck liked post by Brian On thread : Lever guns - What do ya reckon?

    If you change from a bolt to a lever or semi you need to retrain your instinctive shooting or you will fire one shot and grab for the bolt handle.

    Liked On: 17-07-2023, 06:08 PM

14. 
    Got-ya liked post by Brian On thread : Lever guns - What do ya reckon?

    If you change from a bolt to a lever or semi you need to retrain your instinctive shooting or you will fire one shot and grab for the bolt handle.

    Liked On: 17-07-2023, 05:42 PM

15. 
    GSP HUNTER liked post by Brian On thread : Lever guns - What do ya reckon?

    If you change from a bolt to a lever or semi you need to retrain your instinctive shooting or you will fire one shot and grab for the bolt handle.

    Liked On: 17-07-2023, 05:35 PM

Page 11 of 64 First 1234567891011121314151617181920212223242561 ... Last

• Jump to page: