chainsaw
Member

2723 Likes

Page 13 of 182 First 12345678910111213141516171819202122232425262763113 ... Last

• Jump to page:

1. 
   Floundering Around liked post by chainsaw On thread : Tikka 7mm rem mag -OAL

   Plenty of 2225 around of late

   Liked On: 08-09-2023, 03:39 PM

2. 
   makka liked post by chainsaw On thread : New (to me) chambering

   No, Truflite did the work for me.

   Liked On: 06-09-2023, 10:46 AM

3. 
   Moa Hunter liked post by chainsaw On thread : New (to me) chambering

   2506 is a very capable caliber for nz hunting out to 300yds. I’ve had a couple in the past, when came time to re-barrel I stepped it up to 6506ai. That’s a whole different ball game. 140 AMAX running...

   Liked On: 06-09-2023, 07:09 AM

4. 
   makka liked post by chainsaw On thread : New (to me) chambering

   2506 is a very capable caliber for nz hunting out to 300yds. I’ve had a couple in the past, when came time to re-barrel I stepped it up to 6506ai. That’s a whole different ball game. 140 AMAX running...

   Liked On: 05-09-2023, 09:23 PM

5. 
   Bos liked post by chainsaw On thread : New (to me) chambering

   2506 is a very capable caliber for nz hunting out to 300yds. I’ve had a couple in the past, when came time to re-barrel I stepped it up to 6506ai. That’s a whole different ball game. 140 AMAX running...

   Liked On: 05-09-2023, 03:57 PM

6. 
   Bagheera liked post by chainsaw On thread : Ballistic truing conundrum

   Thanks all for the comments and feedback. To pick up on a couple of points above : BC - i used 0.67 G1 as listed by Hornady. If anything manufacturers stated BCs tend to be “optimistic” and...

   Liked On: 04-09-2023, 10:00 AM

7. 
   Bagheera liked post by chainsaw On thread : Ballistic truing conundrum

   We are about 80m above sea level, pressure according to weather maps past few days is 1015 - 1020 hPa. Can’t see that changing anything much. Also any air pressure factors should be covered with...

   Liked On: 04-09-2023, 09:58 AM

8. 
   11mms liked post by chainsaw On thread : Ballistic truing conundrum

   I want to understand “the why”. That’s the way my brain works & as andyanimal31 says confidence in data is critical. Last thing you need is the double guessing yourself. If the dope came in low,...

   Liked On: 02-09-2023, 05:00 PM

9. 
   tikka liked post by chainsaw On thread : Ballistic truing conundrum

   Zeroing done at 100 yards, see other post below. I never use metres, all measurements are inches, yards, moa, etc. The 200 zero might be 205 or 195, but that makes naff all difference - maybe 0.1 or...

   Liked On: 02-09-2023, 12:38 PM

10. 
    rewa liked post by chainsaw On thread : Breaking in the 260rem and load development

    And make sure the mag box is not binding

    Liked On: 21-08-2023, 03:51 PM

11. 
    FRST liked post by chainsaw On thread : Centennial Wapiti trip

    Excellent, some very cool history. Thanks for sharing

    Liked On: 20-08-2023, 08:57 PM

12. 
    flock liked post by chainsaw On thread : Short barrel powders (308 and 7mm RM)

    +1 for what Kelton advised. If you can’t get 2206 then 2208 will work fine in your 308

    Liked On: 18-08-2023, 10:58 PM

13. 
    No.3 liked post by chainsaw On thread : What magnification are you running in the bush?

    2-12 or 2-10. Extra mag at top end very handy when you need to take a longer shot.

    Liked On: 14-08-2023, 05:59 PM

14. 
    terryf liked post by chainsaw On thread : Bark river knives

    Do some Google search on them. May be not the standard they used to be? There are several very good local NZ knife makers on the forum. And KnivesforAfrica (Terry) on here. You’re blessed with...

    Liked On: 14-08-2023, 04:22 PM

15. 
    Ned liked post by chainsaw On thread : Bark river knives

    Do some Google search on them. May be not the standard they used to be? There are several very good local NZ knife makers on the forum. And KnivesforAfrica (Terry) on here. You’re blessed with...

    Liked On: 14-08-2023, 04:21 PM

Page 13 of 182 First 12345678910111213141516171819202122232425262763113 ... Last

• Jump to page: