ChrisW
Member

822 Likes

Page 26 of 55 First ... 1213141516171819202122232425262728293031323334353637383940 ... Last

• Jump to page:

1. 
   Micky Duck liked post by ChrisW On thread : Replica Winchesters for the chop??

   Uberti 1866 is on the price list. $2,375 in near new condition. Link here, near the bottom of page 10...

   Liked On: 18-11-2019, 06:18 PM

2. 
   Russian 22. liked post by ChrisW On thread : Are Toz .22 ok?

   It looks ok to me especially for $120. A couple hours work and it would probably be a nice wee gun. A bit of sandpaper, elbow grease, and some oil or varnish for the stock. A scotchbrite pad with...

   Liked On: 14-11-2019, 10:56 PM

3. 
   10-Ring liked post by ChrisW On thread : Are Toz .22 ok?

   It looks ok to me especially for $120. A couple hours work and it would probably be a nice wee gun. A bit of sandpaper, elbow grease, and some oil or varnish for the stock. A scotchbrite pad with...

   Liked On: 14-11-2019, 09:52 PM

4. 
   Steve123 liked post by ChrisW On thread : Are Toz .22 ok?

   Iv had an old USSR made toz (cock on closing) for perhaps 13 years. (to3 17-03 I think?) I really like it. Its lightweight, has dual extractors & very strong firing pin spring = super reliability....

   Liked On: 13-11-2019, 10:44 PM

5. 
   10-Ring liked post by ChrisW On thread : Are Toz .22 ok?

   Iv had an old USSR made toz (cock on closing) for perhaps 13 years. (to3 17-03 I think?) I really like it. Its lightweight, has dual extractors & very strong firing pin spring = super reliability....

   Liked On: 13-11-2019, 10:38 PM

6. 
   rewa liked post by ChrisW On thread : Are Toz .22 ok?

   Iv had an old USSR made toz (cock on closing) for perhaps 13 years. (to3 17-03 I think?) I really like it. Its lightweight, has dual extractors & very strong firing pin spring = super reliability....

   Liked On: 13-11-2019, 01:51 PM

7. 
   mimms2 liked post by ChrisW On thread : Are Toz .22 ok?

   Iv had an old USSR made toz (cock on closing) for perhaps 13 years. (to3 17-03 I think?) I really like it. Its lightweight, has dual extractors & very strong firing pin spring = super reliability....

   Liked On: 13-11-2019, 01:19 PM

8. 
   Moa Hunter liked post by ChrisW On thread : 6.5 cartridges listed on Quickload

   Have not read whole thread, but I would think that all you would need to do to get it fairly accurate with an AI /wildcat cartridge is to run it as the parent cartridge, but alter the case capacity...

   Liked On: 09-11-2019, 08:53 AM

9. 
   mopheadrob liked post by ChrisW On thread : preferred brass brands

   My preferred brass is not necessarily the best brass. I mostly use Federal or Hornady due to reasonable price, being readily available, and being good enough for what I do. I place a heavy emphasis...

   Liked On: 07-11-2019, 07:11 PM

10. 
    Mooseman liked post by ChrisW On thread : Typical cold/clean bore effect?

    I clean everything out of my barrels after each outing. Both Carbon & Copper. Cleaning rods, jags, patches, brushes, and solvent. Whether I shoot 5 rounds or a hundred. Clean bore shot is usually...

    Liked On: 06-11-2019, 09:38 PM

11. 
    10-Ring liked post by ChrisW On thread : Typical cold/clean bore effect?

    I clean everything out of my barrels after each outing. Both Carbon & Copper. Cleaning rods, jags, patches, brushes, and solvent. Whether I shoot 5 rounds or a hundred. Clean bore shot is usually...

    Liked On: 06-11-2019, 08:34 AM

12. 
    akaroa1 liked post by ChrisW On thread : How to get fast twist barrels in NZ

    Sounds like the goal is to get the heaviest, highest BC possible projectile, shooting at just under the speed of sound, out of a short action. Sound about right? Its not very unique, but...

    Liked On: 05-11-2019, 05:06 PM

13. 
    Nick-D liked post by ChrisW On thread : Gun Porn, show off your new toys

    Yep.

    Liked On: 05-11-2019, 04:30 PM

14. 
    zimmer liked post by ChrisW On thread : Typical cold/clean bore effect?

    I clean everything out of my barrels after each outing. Both Carbon & Copper. Cleaning rods, jags, patches, brushes, and solvent. Whether I shoot 5 rounds or a hundred. Clean bore shot is usually...

    Liked On: 05-11-2019, 10:00 AM

15. 
    johnd liked post by ChrisW On thread : Looking to get quickload

    If you have measured your case volume, and all other data is correct. Then you would alter the start pressure in order to get it to match your real world velocity. Start pressure can be used to take...

    Liked On: 29-10-2019, 07:05 PM

Page 26 of 55 First ... 1213141516171819202122232425262728293031323334353637383940 ... Last

• Jump to page: