csmiffy
Member

3681 Likes

Page 111 of 246 First ... 1161979899100101102103104105106107108109110111112113114115116117118119120121122123124125161211 ... Last

• Jump to page:

1. 
   csmiffy liked post by Micky Duck On thread : Mauser feeding and floorplate

   all the bits are here gathering dust from the model70 lightweight if needed....

   Liked On: 15-01-2022, 07:18 PM

2. 
   csmiffy liked post by akaroa1 On thread : Mauser feeding and floorplate

   csmiffy put up an image of the spring you have and I will see if it is like any in my hoard

   Liked On: 15-01-2022, 05:24 PM

3. 
   csmiffy liked post by Fat belly Dog On thread : Snapper and crabs -on the Baby Q island style

   Got some fresh snapper and frozen crabs from the local fish shop, watercress and banana leaves from mums place, Dinner sorted, heavy buttered and salted steamed snapper wrapped in watercress...

   Liked On: 15-01-2022, 10:25 AM

4. 
   csmiffy liked post by 55six On thread : Conotech Monocular

   If you want to test one in store we are only an hours drive away on the kapiti coast.

   Liked On: 15-01-2022, 08:32 AM

5. 
   csmiffy liked post by gundoc On thread : 308 vs 30/06

   With normal barrel lengths and 150 grain bullets there is little difference between the two cartridges out to 350 metres, beyond that the .30/06 is a bit flatter, and can be handloaded to about 3000...

   Liked On: 13-01-2022, 04:17 PM

6. 
   csmiffy liked post by Frogfeatures On thread : 308 vs 30/06

   223 and 243, with a 44/40 just to keep things interesting To be fair, it’s probably more a want than a need, but hey I can find space in the gun safe

   Liked On: 13-01-2022, 04:17 PM

7. 
   csmiffy liked post by 7mmsaum On thread : 30 Nosler Powder for Heavys

   ADI2217 does have the edge for temp stability but you mentioned the 230 grainers, ADI 2225 has the heavies covered Good advise needn’t consider availability of components :)

   Liked On: 13-01-2022, 10:17 AM

8. 
   csmiffy liked post by bunji On thread : 300 win mag

   MattyR The archaic system on the forum cut off part of my post, when l tried to add some info ,so here is some more important points ,for you to consider on bullet choice at longer ranges for hunting...

   Liked On: 12-01-2022, 05:12 PM

9. 
   csmiffy liked post by akaroa1 On thread : 22 quick release mounts on a custom high power rifle quarter rib

   https://www.optics-trade.eu/nz/rusan-roll-off-rings-11-mm-rail-25-4-mm-q-r.html I found exactly what I was looking for in SLOVENIA ! And a range of mount heights Has anyone dealt with...

   Liked On: 11-01-2022, 06:07 PM

10. 
    csmiffy liked post by Bill999 On thread : DIY Gunsmithing mistakes

    necking up 280 needs a bulge on the neck larger than the 7mm die makes it you have to go up to 30cal then back to 7mm otherwise the firing pin pushes the 270 bullet forward and strikes the primer...

    Liked On: 09-01-2022, 07:42 PM

11. 
    csmiffy liked post by Rushy On thread : Rossi lever action first round cartridge loading issue

    And this pooling of information gentlemen is what makes this forum such a great place. It turns out that Cigar and gundoc are right on the money and I was not seating the last round loaded far...

    Liked On: 09-01-2022, 01:57 PM

12. 
    csmiffy liked post by gonetropo On thread : DIY Gunsmithing mistakes

    i wont tell anyone about your wiring skills then ................................ :P

    Liked On: 08-01-2022, 04:27 PM

13. 
    csmiffy liked post by akaroa1 On thread : DIY Gunsmithing mistakes

    And here's the one I just did I'm just re barreling a vintage Winchester 1885 action Dialed in the barrel and trueing things up Made the rebate for the breech block front right ridge Then tidy...

    Liked On: 08-01-2022, 04:22 PM

14. 
    csmiffy liked post by akaroa1 On thread : DIY Gunsmithing mistakes

    Well I will kick it off Recently I had the bit between my teeth and wanted to form a 38-303 case from some old CAC 303 sporting ammo Well I didn't know that the powder in that old junk goes...

    Liked On: 08-01-2022, 04:21 PM

15. 
    csmiffy liked post by Hunter_Nick On thread : Walnut stock build (done the traditional way)

    Quick update to this. Been slowly working on the finish, almost ready to start checkering hopefully next week. Pores of the wood 95% filled, just a little more finish required, then a cut back to...

    Liked On: 08-01-2022, 02:07 PM

Page 111 of 246 First ... 1161979899100101102103104105106107108109110111112113114115116117118119120121122123124125161211 ... Last

• Jump to page: