Dan.22-250
Member

111 Likes

Page 6 of 8 First 12345678 Last

• Jump to page:

1. 
   mcche171 liked post by Dan.22-250 On thread : Sako factory ammo one shot, two holes

   Cheers for clearing that up. Turns out my memory wasn't quite right.

   Liked On: 24-03-2022, 09:52 PM

2. 
   Bagheera liked post by Dan.22-250 On thread : rifle set ups

   The name bushpig and superpig I think came from the NZ Hunter show/magazine (may have been a pimp your bush rifle series of articles). The superpig is usually slightly longer barrel and commonly in...

   Liked On: 21-03-2022, 02:59 PM

3. 
   GWH liked post by Dan.22-250 On thread : rifle set ups

   The name bushpig and superpig I think came from the NZ Hunter show/magazine (may have been a pimp your bush rifle series of articles). The superpig is usually slightly longer barrel and commonly in...

   Liked On: 21-03-2022, 02:43 PM

4. 
   RV1 liked post by Dan.22-250 On thread : Gun shop recommendations - Christchurch

   Can't give you any recommendations on a shop as I haven't used Christchurch gun shops enough. Having worked in retail I can say any store will skew towards what they want to sell. The truth of the...

   Liked On: 03-03-2022, 05:44 PM

5. 
   yeah_na_missed liked post by Dan.22-250 On thread : Gun shop recommendations - Christchurch

   Can't give you any recommendations on a shop as I haven't used Christchurch gun shops enough. Having worked in retail I can say any store will skew towards what they want to sell. The truth of the...

   Liked On: 03-03-2022, 01:38 AM

6. 
   Micky Duck liked post by Dan.22-250 On thread : Gun shop recommendations - Christchurch

   Can't give you any recommendations on a shop as I haven't used Christchurch gun shops enough. Having worked in retail I can say any store will skew towards what they want to sell. The truth of the...

   Liked On: 02-03-2022, 09:20 PM

7. 
   Micky Duck liked post by Dan.22-250 On thread : 1 load 2 rifles

   If you're within SAMMI (factory) specs and published data for your cartridge then all will be fine. If you're only partial sizing/bumping shoulder or neck sizing, running higher powder charges or...

   Liked On: 23-02-2022, 09:31 PM

8. 
   7mm Rem Mag liked post by Dan.22-250 On thread : 1 load 2 rifles

   If you're within SAMMI (factory) specs and published data for your cartridge then all will be fine. If you're only partial sizing/bumping shoulder or neck sizing, running higher powder charges or...

   Liked On: 23-02-2022, 07:00 PM

9. 
   norsk liked post by Dan.22-250 On thread : Unknown bolt

   I'd be pretty certain it's a Ruger 77/22 hornet or 77/17 hornet bolt. A couple of small shims between the two parts of the bolt made the old man's much less frustrating (more accurate).

   Liked On: 21-02-2022, 09:46 PM

10. 
    Micky Duck liked post by Dan.22-250 On thread : Unknown bolt

    I'd be pretty certain it's a Ruger 77/22 hornet or 77/17 hornet bolt. A couple of small shims between the two parts of the bolt made the old man's much less frustrating (more accurate).

    Liked On: 21-02-2022, 09:36 PM

11. 
    Micky Duck liked post by Dan.22-250 On thread : Lead in .410 vs steel in 20

    I started out with a Rossi single shot .410 and loved it. Light gun but still very little kick. Then graduated to the same gun in 20 gauge, it kicked pretty bad and the thicker pistol grip and stock...

    Liked On: 20-02-2022, 06:25 PM

12. 
    Moa Hunter liked post by Dan.22-250 On thread : Am I silly in wanting a telescopic fishing rod for trout?

    A telescopic rod isn't going to be as good as a multi piece one, you just can't make them. They'll work fine and you can definitely get some pretty good ones nowadays. If you want a good rod that...

    Liked On: 30-01-2022, 08:26 AM

13. 
    timattalon liked post by Dan.22-250 On thread : Choosing calibre based on ammunition availablitiy

    If you do end up using cup and core ammo the .308 will definitely be hard to beat, some others will have slightly better ballistics but any deer won't care. However if you end up using monos or...

    Liked On: 21-01-2022, 06:25 PM

14. 
    CBH Australia liked post by Dan.22-250 On thread : Full Length or Neck sizing. What is better and why?

    Ideally you want to full length size your case just enough so it has the minimum necessary clearance in the chamber. This means every round is the same, as cases are always sized back to the same...

    Liked On: 19-01-2022, 02:00 PM

15. 
    JohnQT liked post by Dan.22-250 On thread : Full Length or Neck sizing. What is better and why?

    Ideally you want to full length size your case just enough so it has the minimum necessary clearance in the chamber. This means every round is the same, as cases are always sized back to the same...

    Liked On: 17-01-2022, 09:33 PM

Page 6 of 8 First 12345678 Last

• Jump to page: