dannyb
Unapologetic gun slut

13927 Likes

Page 47 of 929 First ... 333435363738394041424344454647484950515253545556575859606197147547 ... Last

• Jump to page:

1. 
   dannyb liked post by 7mmsaum On thread : My 7mm PRC is driving me nuts…

   Same as 162 amax or eldm at 3030-3050 and in the RUMs at 3200fps Seen it very specifically since 2002 Anyone saying differently lacks the particular experience. 259077

   Liked On: 14-09-2024, 11:39 AM

2. 
   dannyb liked post by Stocky On thread : Rifle Stocks

   Anyone imported a rifle stock recently from the US? Wondered how it went and if there were any issues with customs or permits

   Liked On: 14-09-2024, 08:36 AM

3. 
   dannyb liked post by whanahuia On thread : Firearm License unrelated referee

   He should talk with firearms licensing. The In law might be acceptable.

   Liked On: 14-09-2024, 08:08 AM

4. 
   dannyb liked post by 7mmsaum On thread : Hilux inverted leaf springs

   Factory rear springs but add another factory main leaf with the eyes cut off, taper the cut to avoid concentrating load stress at the cut The D bolts are long enough, just make another centre...

   Liked On: 13-09-2024, 11:07 PM

5. 
   dannyb liked post by Tentman On thread : Scope for hunting tops

   Go for the best glass, it will reward you more at first and last light than magnification will at longer ranges. 10x is fine out to at least 400M

   Liked On: 13-09-2024, 09:51 PM

6. 
   dannyb liked post by 7mm Rem Mag On thread : Demise of the 7mm Rem Mag

   The only calibre that could bring about its demise would be the 223

   Liked On: 13-09-2024, 07:41 PM

7. 
   dannyb liked post by akaroa1 On thread : Demise of the 7mm Rem Mag

   Well it's clearly irresponsible and unethical to be using an obsolete caliber like that Shame on you !

   Liked On: 13-09-2024, 07:30 PM

8. 
   dannyb liked post by outdoorlad On thread : DPT brake end cap

   Sika 8 That might explain things….. Comes apart in front of the stainless ok 259042 So these 3 don’t come apart or just the third one should? Cheers 259043

   Liked On: 13-09-2024, 05:57 PM

9. 
   dannyb liked post by EmpireSafaris On thread : Demise of the 7mm Rem Mag

   I’ve been shooting 7mm rem mag for 30 years and will for at least another 30. Mines an old heavy Sako too https://i.postimg.cc/hPQbD4LK/IMG_7918.jpg (https://postimages.org/)

   Liked On: 13-09-2024, 05:52 PM

10. 
    dannyb liked post by Sika 8 On thread : DPT brake end cap

    Remember the front cap first 2 are one piece!

    Liked On: 13-09-2024, 04:14 PM

11. 
    dannyb liked post by outdoorlad On thread : DPT brake end cap

    Well I was going to get one, but despite buying a couple hose clamps I still can’t get the front baffles off, I’m going to take to my mates workshop, worse case I’ll need a new suppressor to go with...

    Liked On: 13-09-2024, 03:51 PM

12. 
    dannyb liked post by Brad S On thread : Hunting fitness

    1. squat down and back up with large amounts of weight on a regular basis 2. commute 14km daily on ebike in the Dunedin hills 3. take gun for a walk at least once a week 259008259009259010

    Liked On: 13-09-2024, 08:20 AM

13. 
    dannyb liked post by John Duxbury On thread : Powder recommendations for short barrel 308?

    Basically the powder that gets the highest velocity in a long barrel will get the highest velocity in a short barrel. This idea that shorter barrels benefit from a faster burning powder is not really...

    Liked On: 12-09-2024, 04:48 PM

14. 
    dannyb liked post by Longrun On thread : Costly Mistake.

    There's no tenon machined on that one either.

    Liked On: 12-09-2024, 05:52 AM

15. 
    dannyb liked post by Tentman On thread : Costly Mistake.

    I'm not sure the barrel pictured is part of the rifle in question - who fits and chambers a rifle with the ends still on the blank . ... . It's a no-no

    Liked On: 12-09-2024, 05:52 AM

Page 47 of 929 First ... 333435363738394041424344454647484950515253545556575859606197147547 ... Last

• Jump to page: