dogmatix
Member

2211 Likes

Page 4 of 148 First 12345678910111213141516171854104 ... Last

• Jump to page:

1. 
   Mick Hunter liked post by dogmatix On thread : Tikka Ace

   Geoff at TheGunRack is bringing in Vision Chassis, including a Vision front end (https://visionprc.com/product/krg-competition-frontguard-upgrade-tikka-sa/) that will go on your existing KRG chassis....

   Liked On: 20-01-2025, 12:11 PM

2. 
   Bobba liked post by dogmatix On thread : 22lr Practicle rifle setup

   Gillie SixtyTen

   Liked On: 17-01-2025, 09:38 AM

3. 
   25/08 IMP liked post by dogmatix On thread : Super light thinking

   Something 6.5.

   Liked On: 05-01-2025, 03:33 PM

4. 
   timattalon liked post by dogmatix On thread : Super light thinking

   Something 6.5.

   Liked On: 05-01-2025, 01:35 PM

5. 
   Russian 22. liked post by dogmatix On thread : Info wanted on .303

   Without knowing the barrel condition, its hard to say. Judging by the target sight and the fact its had the normal rear sight removed and the woodwork modified for that purpose, it might have been...

   Liked On: 04-01-2025, 08:42 PM

6. 
   earplay liked post by dogmatix On thread : Info wanted on .303

   Without knowing the barrel condition, its hard to say. Judging by the target sight and the fact its had the normal rear sight removed and the woodwork modified for that purpose, it might have been...

   Liked On: 04-01-2025, 07:20 PM

7. 
   Rich007 liked post by dogmatix On thread : DPT help

   Or do a home job and get a 3 or 4 jaw lathe chuck for your drill. ...

   Liked On: 18-12-2024, 09:42 PM

8. 
   jaacko liked post by dogmatix On thread : DPT help

   You need to turn the bushing on a lathe to fit. DPT can do this for you, as could an engineering shop or home hobbyist. Just measure the barrel diameter at the point where the bushing will go.

   Liked On: 18-12-2024, 07:01 PM

9. 
   Mrfants liked post by dogmatix On thread : Sako lovers

   75 Finnlight in... cough... cough... 270Win. 249066 75 Stainless Laminate 223Rem (1 in 8") 249067 Both with DPT cans and both with spare factory mags.

   Liked On: 29-11-2024, 07:46 PM

10. 
    Micky Duck liked post by dogmatix On thread : Brass on bolt face

    Some of the Hornady factory ammo, especially 'super performance' can be pretty hot if you have a tight chamber. I was getting pressure signs with it in my 6.5 Grendel. Extractor marks on brass,...

    Liked On: 25-11-2024, 04:09 PM

11. 
    Dan88 liked post by dogmatix On thread : Brass on bolt face

    I assume the Hornady case is on the right, based on the PPU/Highland anneal mark. Bit of a bulge in the case side wall. 'Could be' pressure related and that might fit in with the brass on the bolt...

    Liked On: 24-11-2024, 08:47 PM

12. 
    7mmsaum liked post by dogmatix On thread : Brass on bolt face

    Some of the Hornady factory ammo, especially 'super performance' can be pretty hot if you have a tight chamber. I was getting pressure signs with it in my 6.5 Grendel. Extractor marks on brass,...

    Liked On: 24-11-2024, 04:34 PM

13. 
    takbok liked post by dogmatix On thread : Rifle shooting to right query

    As other have mentioned. 2 shot groups don't tell you anything. You need 5 shot groups. Check scope is level with receiver with something better than mark 1 eyeball and zero it at 200m. Not 100m

    Liked On: 31-10-2024, 08:28 AM

14. 
    Micky Duck liked post by dogmatix On thread : Rifle shooting to right query

    As other have mentioned. 2 shot groups don't tell you anything. You need 5 shot groups. Check scope is level with receiver with something better than mark 1 eyeball and zero it at 200m. Not 100m

    Liked On: 30-10-2024, 03:17 PM

15. 
    outlander liked post by dogmatix On thread : Alfa 357 carbine, current value ?

    Fixed your post MD. ;)

    Liked On: 28-10-2024, 10:15 AM

Page 4 of 148 First 12345678910111213141516171854104 ... Last

• Jump to page: