flock
Member

510 Likes

Page 23 of 34 First ... 910111213141516171819202122232425262728293031323334 Last

• Jump to page:

1. 
   flock liked post by Three O'Three On thread : Lee Collet Die Decapping Pin Removed

   There maybe some confusion with my original question? I wasn't referring to operating a collet die without the mandrel but cutting the decapping pin off the mandrel and operating the die with a...

   Liked On: 07-08-2022, 01:35 PM

2. 
   flock liked post by Cyclops On thread : Ultrasonic cleaner tips please

   The steps I folllow Deprime inspect cases Anneal - every 5th use Full length size Ultrasonic clean oven dry at low heat (120 C), air cool on clean towel inspect cases prime, load with...

   Liked On: 05-08-2022, 08:31 AM

3. 
   flock liked post by johnd On thread : Lee Collet Die Decapping Pin Removed

   You can buy spare mandrels, I have done this and have one without the pin on the end for the same purpose as above regarding not disturbing a live primer. I have gone back to using full length...

   Liked On: 03-08-2022, 04:30 PM

4. 
   flock liked post by Billbob On thread : What little pesties did you bowl over today?

   Shot this over a year ago while stalking another wallaby when this one popped its head up about 10m away from me. Slocked a pellet straight between the ears when it turned its head. Hatsan 125...

   Liked On: 02-08-2022, 01:59 PM

5. 
   flock liked post by Localman On thread : What little pesties did you bowl over today?

   Having breakfast this morning, rabbit runs out on to lawn and round garden. Get PCP out ,step outside and it runs away, finish coffee. 5 minutes later 2 rabbits come out ,one shot one dead[ rabbit....

   Liked On: 31-07-2022, 01:46 PM

6. 
   flock liked post by Micky Duck On thread : Call to End Firearms Advertising.

   Im really regretting posting reply to this at all........ IN NO WAY was I trying to lower the tone or make a personal attack...purely pointing out that adds are not for everyone,and if one section of...

   Liked On: 22-07-2022, 10:17 PM

7. 
   flock liked post by Bol Tackshin On thread : Call to End Firearms Advertising.

   308 - Agree wholeheartedly with what you said. Cigarettes and alcohol cause harm, and that is why advertising them is now in the naughty corner. Firearms could easily follow suit. I agree we need to...

   Liked On: 22-07-2022, 10:17 PM

8. 
   flock liked post by scotty On thread : Call to End Firearms Advertising.

   well then lets just use this stupid logic...... ban university advertising cos anyone who wants to go knows where they are. ban ads for KFC and other fast foods everyone knows where they are and ...

   Liked On: 21-07-2022, 08:44 PM

9. 
   flock liked post by Micky Duck On thread : Call to End Firearms Advertising.

   well you tell Mrs Cook from me I do not need to see feminine hygene products advertised on TV when Im eating my dinner at night either but the broadcasting standards authority thinks its ok for them...

   Liked On: 21-07-2022, 08:39 PM

10. 
    flock liked post by No.3 On thread : STRAIGHTENING A CROOKED BULLET

    When seating, seat it half way then retract the case, turn it 180deg and run it to full depth. Seems to fix most of this issue. Another cause is a mismatch between the tip of the bullet and the...

    Liked On: 11-07-2022, 09:35 PM

11. 
    flock liked post by gundoc On thread : Rechambering question for you experienced machinists

    Go to the SAAMI pages and compare the differences between maximum cartridge dimensions and minimum chamber dimensions and you will get the tolerances you need for designing chamber and loading die...

    Liked On: 10-07-2022, 10:07 PM

12. 
    flock liked post by Woody On thread : STRAIGHTENING A CROOKED BULLET

    I use a lee collet mandrel neck sizer after normal resizing/shoulder bump.

    Liked On: 10-07-2022, 01:45 PM

13. 
    flock liked post by GWH On thread : What little pesties did you bowl over today?

    Had a session on Sat evening with twin Tikka T1x 17hmrs. A mate really liked using mine so he got one for himself and I helped out setting it up. Mounting a scope, zeroing and validating drop to...

    Liked On: 03-07-2022, 09:28 PM

14. 
    flock liked post by shift14 On thread : The dinner plate challenge

    I’m fortunate enough to be able to verify on a 1m x 1m plate at 565 or 615 yds. 200742 60mm dots B

    Liked On: 03-07-2022, 04:34 PM

15. 
    flock liked post by andyanimal31 On thread : Zeroing: Getting too cocky leads to cockups

    45 yrs ago that applied as the scope mechanisms that we had were pretty agriculture and was common practice. I would be pretty disappointed if I had to do any tapping or going past the adjustment...

    Liked On: 02-07-2022, 10:28 PM

Page 23 of 34 First ... 910111213141516171819202122232425262728293031323334 Last

• Jump to page: