Fssprecision
Member

727 Likes

Page 2 of 49 First 12345678910111213141516 ... Last

• Jump to page:

1. 
   short swede liked post by Fssprecision On thread : Unusual early knife/pistol

   You sure don't see many of these about, this came along this week and needed the old broken nipple removing and a new one making. turned out great and a lovely little piece

   Liked On: 22-05-2024, 05:08 PM

2. 
   Ross Nolan liked post by Fssprecision On thread : Unusual early knife/pistol

   You sure don't see many of these about, this came along this week and needed the old broken nipple removing and a new one making. turned out great and a lovely little piece

   Liked On: 22-05-2024, 02:32 PM

3. 
   Marty Henry liked post by Fssprecision On thread : Unusual early knife/pistol

   You sure don't see many of these about, this came along this week and needed the old broken nipple removing and a new one making. turned out great and a lovely little piece

   Liked On: 22-05-2024, 02:31 PM

4. 
   FRST liked post by Fssprecision On thread : Shout out to FSS Precsion/Darren

   Great feedback, happy to help :-)

   Liked On: 09-05-2024, 09:08 AM

5. 
   Micky Duck liked post by Fssprecision On thread : Shout out to FSS Precsion/Darren

   Great feedback, happy to help :-)

   Liked On: 08-05-2024, 11:51 AM

6. 
   AR7 liked post by Fssprecision On thread : Ruger 10/22 rotary mag issues

   Clean is the key and I have always used this principal to re tension the spring with no feeding problems.. Using one of the flat hexagon edges as reference, that edge must be turned clockwise...

   Liked On: 27-04-2024, 05:32 PM

7. 
   Tapawera liked post by Fssprecision On thread : Ruger 10/22 rotary mag issues

   Clean is the key and I have always used this principal to re tension the spring with no feeding problems.. Using one of the flat hexagon edges as reference, that edge must be turned clockwise...

   Liked On: 27-04-2024, 05:28 PM

8. 
   AR7 liked post by Fssprecision On thread : RPR RIMFIRE RAIL SLOTS NOT DEEP ENOUGH

   I have sorted a few rails with shallow rail slots, stayer was one I remember. Really want to do on a mill to do properly

   Liked On: 20-04-2024, 08:18 PM

9. 
   NIMROD liked post by Fssprecision On thread : DPT Supressor bush sizing

   That is what I do and have a section of barrel at least that eccentric to show people …… that is why I seldom post on here, too many experts!

   Liked On: 20-04-2024, 04:43 PM

10. 
    MB liked post by Fssprecision On thread : DPT Supressor bush sizing

    That is what I do and have a section of barrel at least that eccentric to show people …… that is why I seldom post on here, too many experts!

    Liked On: 19-04-2024, 11:20 PM

11. 
    norsk liked post by Fssprecision On thread : SMLE, what's it worth?

    Prices down recently, with the last few through auction getting $500-$700

    Liked On: 14-04-2024, 07:41 PM

12. 
    ZQLewis liked post by Fssprecision On thread : Ghost silencer bush, do I need one?

    I would be happy to help bore it out on the lathe if you get the new bush. FYI they must be a good clearance on the barrel, I have many barrel off cuts here where the bore is not concentric to the...

    Liked On: 08-04-2024, 08:17 PM

13. 
    AR7 liked post by Fssprecision On thread : 50 Cal can

    You don't see these everyday, a mate got hold of a genuine 50 Cal suppressor, todays task was to make an adaptor to fit it to his gun. Will be interesting to see/hear how it performs, this is one...

    Liked On: 06-04-2024, 09:26 AM

14. 
    dannyb liked post by Fssprecision On thread : 50 Cal can

    You don't see these everyday, a mate got hold of a genuine 50 Cal suppressor, todays task was to make an adaptor to fit it to his gun. Will be interesting to see/hear how it performs, this is one...

    Liked On: 05-04-2024, 07:42 PM

15. 
    makka liked post by Fssprecision On thread : Ghost silencer bush, do I need one?

    Nothing to think about, easy job in the lathe and I would do for free while you wait :-).....I have a long line of customers who had a go with a file or sand paper ha ha ha

    Liked On: 05-04-2024, 12:36 PM

Page 2 of 49 First 12345678910111213141516 ... Last

• Jump to page: