Fssprecision
Member

972 Likes

Page 49 of 65 First ... 3536373839404142434445464748495051525354555657585960616263 ... Last

• Jump to page:

1. 
   rugerman liked post by Fssprecision On thread : Great to teach an enthusiastic youngster

   I am currently helping a young lad learn a bit about Engineering so came up with this little support jack as a project to include a few interesting machined parts. I just made one for me before he...

   Liked On: 22-07-2022, 08:27 PM

2. 
   Bol Tackshin liked post by Fssprecision On thread : Great to teach an enthusiastic youngster

   I am currently helping a young lad learn a bit about Engineering so came up with this little support jack as a project to include a few interesting machined parts. I just made one for me before he...

   Liked On: 22-07-2022, 07:50 PM

3. 
   Joe_90 liked post by Fssprecision On thread : 38 Spl Carbine

   Hope so, tool for a job, I might even put a bayonet lug on it ha ha ha.

   Liked On: 16-07-2022, 09:05 PM

4. 
   Bill999 liked post by Fssprecision On thread : 38 Spl Carbine

   Hope so, tool for a job, I might even put a bayonet lug on it ha ha ha.

   Liked On: 15-07-2022, 11:41 AM

5. 
   Micky Duck liked post by Fssprecision On thread : 38 Spl Carbine

   I have had a length of 38/357 barrel blank lying around for a while now and finally got some time to do something with it. Using a new 410 action as a base, I machined the barrel blank to fit,...

   Liked On: 14-07-2022, 07:41 PM

6. 
   rossi.45 liked post by Fssprecision On thread : 38 Spl Carbine

   I have had a length of 38/357 barrel blank lying around for a while now and finally got some time to do something with it. Using a new 410 action as a base, I machined the barrel blank to fit,...

   Liked On: 14-07-2022, 07:58 AM

7. 
   Bol Tackshin liked post by Fssprecision On thread : 38 Spl Carbine

   Thanks, don't know if I will spend time developing a load, most likely pass it on now. No I just chambered for 38 given that it is similar pressure to 410.

   Liked On: 14-07-2022, 07:46 AM

8. 
   40mm liked post by Fssprecision On thread : 38 Spl Carbine

   I have had a length of 38/357 barrel blank lying around for a while now and finally got some time to do something with it. Using a new 410 action as a base, I machined the barrel blank to fit,...

   Liked On: 13-07-2022, 10:40 PM

9. 
   Bol Tackshin liked post by Fssprecision On thread : 38 Spl Carbine

   I have had a length of 38/357 barrel blank lying around for a while now and finally got some time to do something with it. Using a new 410 action as a base, I machined the barrel blank to fit,...

   Liked On: 13-07-2022, 10:22 PM

10. 
    7mmwsm liked post by Fssprecision On thread : 38 Spl Carbine

    I have had a length of 38/357 barrel blank lying around for a while now and finally got some time to do something with it. Using a new 410 action as a base, I machined the barrel blank to fit,...

    Liked On: 13-07-2022, 10:17 PM

11. 
    Pengy liked post by Fssprecision On thread : Clip on NV help

    Owl can always supply specials like the above...I make it for them.

    Liked On: 11-07-2022, 03:23 PM

12. 
    Trout liked post by Fssprecision On thread : Clip on NV help

    If you were after something like this, I can machine what sizes you want.

    Liked On: 10-07-2022, 06:21 PM

13. 
    tetawa liked post by Fssprecision On thread : Clip on NV help

    If you were after something like this, I can machine what sizes you want.

    Liked On: 10-07-2022, 01:44 PM

14. 
    TLB liked post by Fssprecision On thread : Clip on NV help

    If you were after something like this, I can machine what sizes you want.

    Liked On: 10-07-2022, 12:51 PM

15. 
    ZQLewis liked post by Fssprecision On thread : Something special

    Had something really special come along recently, this lovely old presentation Adams revolver. Not very often you get to see guns of this quality and in particularly good condition given its age...

    Liked On: 10-07-2022, 12:21 AM

Page 49 of 65 First ... 3536373839404142434445464748495051525354555657585960616263 ... Last

• Jump to page: