gqhoon
Member

294 Likes

Page 1 of 20 123456789101112131415 ... Last

• Jump to page:

1. 
   6x47 liked post by gqhoon On thread : Carbon fibre stock help

   PM me your address and I’ll send you a spare Gunworks recoil lug I have.

   Liked On: 12-03-2024, 03:25 PM

2. 
   kiwijames liked post by gqhoon On thread : Carbon fibre stock help

   PM me your address and I’ll send you a spare Gunworks recoil lug I have.

   Liked On: 11-03-2024, 09:47 PM

3. 
   veitnamcam liked post by gqhoon On thread : Carbon fibre stock help

   PM me your address and I’ll send you a spare Gunworks recoil lug I have.

   Liked On: 11-03-2024, 09:00 PM

4. 
   MPR liked post by gqhoon On thread : Carbon fibre stock help

   PM me your address and I’ll send you a spare Gunworks recoil lug I have.

   Liked On: 11-03-2024, 08:50 PM

5. 
   Shearer liked post by gqhoon On thread : Carbon fibre stock help

   PM me your address and I’ll send you a spare Gunworks recoil lug I have.

   Liked On: 11-03-2024, 08:17 PM

6. 
   ZQLewis liked post by gqhoon On thread : Impossible 6mm ??

   A GT will easily do 3,000fps with a 105gr class projectile, loaded at normal length. But at 2.4” COAL, the boat tail will be well below at case neck shoulder junction, so a 95gr might be easier to...

   Liked On: 11-02-2024, 10:46 PM

7. 
   kiwi303 liked post by gqhoon On thread : Impossible 6mm ??

   A GT will easily do 3,000fps with a 105gr class projectile, loaded at normal length. But at 2.4” COAL, the boat tail will be well below at case neck shoulder junction, so a 95gr might be easier to...

   Liked On: 08-02-2024, 02:27 PM

8. 
   timattalon liked post by gqhoon On thread : Armageddon Gear Order

   Hit up Geoff from the GunRack to see when he’s getting an order in from Armageddon next. Might save yourself a few dollars.

   Liked On: 09-11-2023, 04:58 AM

9. 
   BenTheBuilder liked post by gqhoon On thread : FL resized rounds wont chamber

   Ben, find brass that meets the criteria below 1 - Factory round, pull the projectile and dump powder, confirm it fits in your chamber 2- case fired in your chamber, sized and fits back in your...

   Liked On: 14-08-2023, 12:58 PM

10. 
    buzzman liked post by gqhoon On thread : Primer question

    I doubt it. When seating the primer into the pocket, it requires a small amount of crush as the edges of the cup bottoms out on the base of the pocket and pushes the anvil up into the primer paste to...

    Liked On: 05-07-2023, 02:30 AM

11. 
    zimmer liked post by gqhoon On thread : Tikka T3X barrel break-in

    I think this is the most significant aspect of breaking-in a barrel, in that it’s actually the chamber / bore transition that needs the attention. I’ll use abrasives on a patch and short-stroke this...

    Liked On: 04-07-2023, 09:46 AM

12. 
    Larskramer liked post by gqhoon On thread : 7mm ss cs 7mm saum vs 7mmsst

    Shehane isn’t AI ‘improved’. Just has less body taper compared to standard 284W and increases powder capacity by about 3grains or so. 7-6.5PRC has similar capacity, but just does the same job easier.

    Liked On: 26-06-2023, 10:28 PM

13. 
    Kelton liked post by gqhoon On thread : 7mm ss cs 7mm saum vs 7mmsst

    Shehane isn’t AI ‘improved’. Just has less body taper compared to standard 284W and increases powder capacity by about 3grains or so. 7-6.5PRC has similar capacity, but just does the same job easier.

    Liked On: 26-06-2023, 09:01 PM

14. 
    Micky Duck liked post by gqhoon On thread : 7mm ss cs 7mm saum vs 7mmsst

    7-6.5PRC is becoming very popular in F-Class circles….2950fps with 180 Hybrids comfortably with 30” barrel and without needing to push it hard. Achieves 284 Shehane performance without trashing brass.

    Liked On: 26-06-2023, 07:46 PM

15. 
    Kelton liked post by gqhoon On thread : 7mm ss cs 7mm saum vs 7mmsst

    7-6.5PRC is becoming very popular in F-Class circles….2950fps with 180 Hybrids comfortably with 30” barrel and without needing to push it hard. Achieves 284 Shehane performance without trashing brass.

    Liked On: 26-06-2023, 07:15 PM

Page 1 of 20 123456789101112131415 ... Last

• Jump to page: