grandpamac
Member

4758 Likes

Page 153 of 318 First ... 53103139140141142143144145146147148149150151152153154155156157158159160161162163164165166167203253 ... Last

• Jump to page:

1. 
   Tertle liked post by grandpamac On thread : A Free .303

   Greetings All, Today was a crappy day here in HB, a good day to potter about in the shed. As previously reported I was given an old No1 Lee Enfield a few weeks back. As you can see it's a bit rough...

   Liked On: 09-08-2022, 03:47 PM

2. 
   Bill999 liked post by grandpamac On thread : A Free .303

   Greetings All, Today was a crappy day here in HB, a good day to potter about in the shed. As previously reported I was given an old No1 Lee Enfield a few weeks back. As you can see it's a bit rough...

   Liked On: 09-08-2022, 03:42 PM

3. 
   dannyb liked post by grandpamac On thread : A Free .303

   Greetings All, Today was a crappy day here in HB, a good day to potter about in the shed. As previously reported I was given an old No1 Lee Enfield a few weeks back. As you can see it's a bit rough...

   Liked On: 09-08-2022, 03:37 PM

4. 
   caberslash liked post by grandpamac On thread : The future of 300 magnums in nz ????

   Greetings All, I think absolute crap is the right description for the supposed rumor. This type of shit circulates freely in the US and likely will continue to do so. That said, with the number of...

   Liked On: 08-08-2022, 06:38 PM

5. 
   Huk liked post by grandpamac On thread : subs in a saum

   Hodgdon specifies a minimum of 60% of case capacity for Trail Boss and gives 16.3 grains as a minimum start load in the 300 WSM with the 150 grain so I would not go below 60% of capacity which would...

   Liked On: 08-08-2022, 06:12 PM

6. 
   HJA8 liked post by grandpamac On thread : Pull throughs

   Greetings All, Pull throughs are fine for wiping out a barrel in the field but to properly clean it the propper rod, jags, brushes, bore guide, patches and solvents are essential. Yes they are not...

   Liked On: 08-08-2022, 04:39 PM

7. 
   caberslash liked post by grandpamac On thread : Cartridge and Rifle Camberings Availability.

   Greetings and thanks everyone, Having seen a number of supply shortages come and go I try to keep a minimum of two years supply of components for at least some of my rifles. To simplify this my...

   Liked On: 08-08-2022, 11:23 AM

8. 
   Magnus liked post by grandpamac On thread : Pull throughs

   Greetings All, Pull throughs are fine for wiping out a barrel in the field but to properly clean it the propper rod, jags, brushes, bore guide, patches and solvents are essential. Yes they are not...

   Liked On: 08-08-2022, 11:18 AM

9. 
   dannyb liked post by grandpamac On thread : subs in a saum

   Greetings Huk, By far the easiest would be to buy a .308 for your sub loads. Hodgdons has plenty of tested data with four different powders for the 190 grain projectile. They also offer reduced load...

   Liked On: 08-08-2022, 11:00 AM

10. 
    bumblefoot liked post by grandpamac On thread : Running Out of Time

    Greetings All, A like from davetapson to my OP reminded me that I have not done an update on progress for a while. In my last post I reported some reversals in the fitness quest but over few last...

    Liked On: 08-08-2022, 10:40 AM

11. 
    RV1 liked post by grandpamac On thread : Cartridge and Rifle Camberings Availability.

    Greetings All, There have been a couple of threads lately on the possible demise of cartridges due to manufacturer disinterest or government edict. I thought I would do an not very scientific survey...

    Liked On: 07-08-2022, 10:17 PM

12. 
    308 liked post by grandpamac On thread : Cartridge and Rifle Camberings Availability.

    Greetings All, There have been a couple of threads lately on the possible demise of cartridges due to manufacturer disinterest or government edict. I thought I would do an not very scientific survey...

    Liked On: 07-08-2022, 10:13 PM

13. 
    RUMPY liked post by grandpamac On thread : Pull throughs

    Greetings All, Pull throughs are fine for wiping out a barrel in the field but to properly clean it the propper rod, jags, brushes, bore guide, patches and solvents are essential. Yes they are not...

    Liked On: 07-08-2022, 09:53 PM

14. 
    257weatherby liked post by grandpamac On thread : Cartridge and Rifle Camberings Availability.

    Greetings All, There have been a couple of threads lately on the possible demise of cartridges due to manufacturer disinterest or government edict. I thought I would do an not very scientific survey...

    Liked On: 07-08-2022, 09:06 PM

15. 
    caberslash liked post by grandpamac On thread : Cartridge and Rifle Camberings Availability.

    Greetings Micky Duck, Thanks for your reply. I was trying to deal with a couple of specific unfounded rumours in the thread so rather glossed over the panic buying that drives temporary shortages....

    Liked On: 07-08-2022, 09:02 PM

Page 153 of 318 First ... 53103139140141142143144145146147148149150151152153154155156157158159160161162163164165166167203253 ... Last

• Jump to page: