gundoc
Member

4190 Likes

Page 276 of 280 First ... 176226262263264265266267268269270271272273274275276277278279280 Last

• Jump to page:

1. 
   Grim liked post by gundoc On thread : 30 06

   I was shooting in upper half of the South Island in those days so they were fairly safe. The only moose I have seen were dead and hanging on a wall (the last one was in the Swazi shop in Levin).

   Liked On: 12-09-2015, 02:40 PM

2. 
   Carpe Diem liked post by gundoc On thread : ice axe and crampons reccomendation

   Taking your boots in to get proper fitting crampons is good advice. An ice axe can be bloody dangerous unless you have it in your hands and your rifle slung across your back. If you need an ice axe...

   Liked On: 13-07-2015, 05:52 PM

3. 
   veitnamcam liked post by gundoc On thread : Slipping scope

   These rings were sold under the Zero brand in the '80's & 90's. They are very weak and I have seen several instances where the clamp screws have been over-tightened, stripping the threads and having...

   Liked On: 30-06-2015, 10:01 PM

4. 
   JRW87 liked post by gundoc On thread : Slipping scope

   These rings were sold under the Zero brand in the '80's & 90's. They are very weak and I have seen several instances where the clamp screws have been over-tightened, stripping the threads and having...

   Liked On: 30-06-2015, 09:33 PM

5. 
   Maca49 liked post by gundoc On thread : Welding to or porting 12gauge barrel

   Suppressors on shotguns, particularly 12 ga, are more trouble than they are worth. They add a lot of weight forward which inhibits your swing, and they are not very quiet, even with subsonic loads. ...

   Liked On: 14-06-2015, 10:20 PM

6. 
   Scouser liked post by gundoc On thread : Aussie moving to NZ

   You will love Otago. Plenty of local hunting, few people, good roads, close to other good hunting areas (South Westland, Stewart Island, Fiordland). Queenstown is nice but a bit 'touristy' and...

   Liked On: 31-03-2015, 08:11 AM

7. 
   PERRISCICABA liked post by gundoc On thread : Help from the knowledge bank

   A 7mm Rem Mag with a good suppressor will do everything you need, and you will not have the aggravation or expense of trying to source ammo or brass for the WSM's, SAUM's or other orphans. Everyone...

   Liked On: 29-03-2015, 11:52 PM

8. 
   Pengy liked post by gundoc On thread : Aussie moving to NZ

   You will love Otago. Plenty of local hunting, few people, good roads, close to other good hunting areas (South Westland, Stewart Island, Fiordland). Queenstown is nice but a bit 'touristy' and...

   Liked On: 29-03-2015, 06:52 PM

9. 
   10-Ring liked post by gundoc On thread : Trigger pull weight.

   When I was in business the lightest weight I would do for a hunting trigger was 2.5lbs (with a creep-free crisp break). The reason was that in winter conditions it is very difficult to feel the...

   Liked On: 27-03-2015, 09:40 PM

10. 
    Desert Rat liked post by gundoc On thread : Can o worms

    You cannot go past a 3 litre HiLux diesel manual. I prefer the Surf, but the double cabs are as good only they cost more. Something in the late 1990's with no more than 220-230,000 K's will last...

    Liked On: 11-03-2015, 04:54 PM

11. 
    Woody liked post by gundoc On thread : excessively tight screws

    Over-tightened screws is a common problem. An easy way to get them loose (assuming they are not loctited) is to get a solid support under the part and find a neat fitting screwdriver. Give the top...

    Liked On: 09-03-2015, 08:50 PM

12. 
    res liked post by gundoc On thread : excessively tight screws

    Over-tightened screws is a common problem. An easy way to get them loose (assuming they are not loctited) is to get a solid support under the part and find a neat fitting screwdriver. Give the top...

    Liked On: 09-03-2015, 02:09 AM

13. 
    veitnamcam liked post by gundoc On thread : excessively tight screws

    Over-tightened screws is a common problem. An easy way to get them loose (assuming they are not loctited) is to get a solid support under the part and find a neat fitting screwdriver. Give the top...

    Liked On: 08-03-2015, 10:51 AM

14. 
    10-Ring liked post by gundoc On thread : excessively tight screws

    Over-tightened screws is a common problem. An easy way to get them loose (assuming they are not loctited) is to get a solid support under the part and find a neat fitting screwdriver. Give the top...

    Liked On: 08-03-2015, 10:41 AM

15. 
    Shearer liked post by gundoc On thread : Rebarrelling a short action Remington

    Don't bother with wildcats, they are more trouble than they are worth. Get a good quality 22" barrel fitted in either 7mm-08 or .308 (shouldn't exceed $800). Either will do the job perfectly well...

    Liked On: 17-02-2015, 12:52 PM

Page 276 of 280 First ... 176226262263264265266267268269270271272273274275276277278279280 Last

• Jump to page: