HNTMAD
Member

2254 Likes

Page 25 of 151 First ... 111213141516171819202122232425262728293031323334353637383975125 ... Last

• Jump to page:

1. 
   NoMis liked post by HNTMAD On thread : Shot out suppressor

   Throw it away, buy a new one, things happen unfortunately Sent from my SM-S911B using Tapatalk

   Liked On: 02-10-2023, 06:03 PM

2. 
   daniel1717 liked post by HNTMAD On thread : Gutting in the field

   Leave it for nature Sent from my SM-S911B using Tapatalk

   Liked On: 01-10-2023, 05:23 PM

3. 
   Moa Hunter liked post by HNTMAD On thread : Gutting in the field

   Leave it for nature Sent from my SM-S911B using Tapatalk

   Liked On: 01-10-2023, 01:04 PM

4. 
   outlander liked post by HNTMAD On thread : Made my first YouTube channel

   Intro vid is great....except for the milking of dead cow.....not showing respect....like other poster I'm not into long intro to each video...small 10 to 20 sec max, I will normally skip them or just...

   Liked On: 27-09-2023, 10:53 AM

5. 
   ariki liked post by HNTMAD On thread : Clements Mill Road Sat 23/09

   Did he think to pull Iverson and let them go in front? Either way not nice. Hamish Sent from my SM-S911B using Tapatalk

   Liked On: 26-09-2023, 09:31 PM

6. 
   Got-ya liked post by HNTMAD On thread : 308 barrel length velocity loss

   I get that, but some are saying they are chopping for easy of handling based on being shorter....when they are not lol Sent from my SM-S911B using Tapatalk

   Liked On: 14-09-2023, 07:39 AM

7. 
   Got-ya liked post by HNTMAD On thread : 308 barrel length velocity loss

   Gunna ask....what do you mean by handier? I see guys chopping for ease of shorted and less tangles in the scrub etc....but really.....guys chop a std no suppressor barrel and suppressor and think...

   Liked On: 14-09-2023, 07:39 AM

8. 
   Bobba liked post by HNTMAD On thread : Dogs in choppers

   Lol....I remember my viz feeling the engine change, she looked up at the rotor spinning, then to me and then tensed up as we left the ground.....I may have had a wee chuckle Sent from my SM-S911B...

   Liked On: 13-09-2023, 09:44 PM

9. 
   jpurdon liked post by HNTMAD On thread : Dogs in choppers

   Pod on first trip also good as you don't have to reassure them lol Sent from my SM-S911B using Tapatalk

   Liked On: 13-09-2023, 07:05 PM

10. 
    Bobba liked post by HNTMAD On thread : Dogs in choppers

    Held onto in the back seat when East Kaweka was flying Sent from my SM-S911B using Tapatalk

    Liked On: 13-09-2023, 05:22 PM

11. 
    Floundering Around liked post by HNTMAD On thread : Gunsmith Lower North Island

    Hey team, After recommendation for a gunsmith in Lower North Island.....looking at a chop and thread for a suppressor and maybe a quick beadblast.... Cheers Hamish Sent from my SM-S911B...

    Liked On: 13-09-2023, 01:38 PM

12. 
    Micky Duck liked post by HNTMAD On thread : 308 barrel length velocity loss

    I must confess I have a 14.5 inch barrel 308...purchased at bits, cut old suppressor thread off hence the 1/2.... It shoots 150gr Sako factory inside 1 moa, it is a bit louder but then noise is...

    Liked On: 12-09-2023, 10:01 AM

13. 
    GSP HUNTER liked post by HNTMAD On thread : 308 barrel length velocity loss

    I must confess I have a 14.5 inch barrel 308...purchased at bits, cut old suppressor thread off hence the 1/2.... It shoots 150gr Sako factory inside 1 moa, it is a bit louder but then noise is...

    Liked On: 12-09-2023, 07:04 AM

14. 
    timattalon liked post by HNTMAD On thread : Change of Address requirements

    Yep, exactly Sent from my SM-S911B using Tapatalk

    Liked On: 02-09-2023, 04:49 AM

15. 
    11mms liked post by HNTMAD On thread : Change of Address requirements

    My thoughts is there will still be a physical inspection, but in meantime send us your pics.....as i would suggest they are overworked and the admin team are colating....and the photos will be...

    Liked On: 01-09-2023, 05:41 PM

Page 25 of 151 First ... 111213141516171819202122232425262728293031323334353637383975125 ... Last

• Jump to page: