Seen a few buzzing around and every Jaffa anniversary they arrive in Dvke.:) Went out for a look. 33349 This one got my attention.:) 33350 Then I saw a green one:ORLY: 33351 Wasn't long and I...
Liked On: 25-01-2015, 06:10 AM
Yep, I have been in the hills up the back of Denver. Man that is rarified air up there, I was out of breath walking between the car and the house.
Liked On: 03-01-2015, 06:56 PM
yeah it was a slot cut into a plate on an angle that part actually worked quite well, it was getting the trigger and charging bars past the magazine that I run into trouble.
Liked On: 02-01-2015, 08:15 AM
hi guys/girls after hunting a local farm for a few years now culling out goats and using them for dog food etc we never really got to see any big boys only ever small to mid size billys but one day...
Liked On: 24-12-2014, 07:45 AM
Hi .303 guy, I suppose there`s a lot of ways of doing this , like a sine ways rifling bar, just have to look on the internet for ideas. I just got lucky with my gearbox and bike bits , and the end...
Liked On: 20-12-2014, 08:35 PM
My god this is pretty basic. If you own an A Cat rifle that the parts fit then you have a perfectly valid reason for having the parts. The case law that Dannz is referring to above wouldn't...
Liked On: 20-12-2014, 08:26 AM
sorry for the odd comment
Liked On: 16-12-2014, 04:26 PM
Went out with my brother to blood his new R8 in 6.5x55mm on the weekend. Took out some dirty red dogs. 32130 32131 32132 32133
Liked On: 15-12-2014, 03:28 PM
Hi ishoot10s, No such luck mate, carn`t put the lathe in drive with the gear box locket up for cutting the octagonal , so yes I`m winding the saddle up and down, up and down, ext .ext,. Say one...
Liked On: 10-12-2014, 08:10 PM
Hi Guys, Now with a bit of work shop magic I have made my lathe an octagonal one, ( no tit pull Toby), made a ali disc to fit on my rifling register with eight holes for lock pin stop. The barrel is...
Liked On: 10-12-2014, 06:34 PM
Figured I'd give this a go I bought this a long while ago now for a fair price I thought, bought rifle and rings, scope is mine Rifle made in 1990. 31838 31839 Shot quite well with factory ammo...
Liked On: 07-12-2014, 07:40 AM
Hi, Yep, just set up and have cut the chamber in my Sharps barrel, I used a t/c form cutter for the job with a 6/7 degree slope into the rifling throat and no lead for these old timers. I used a new...
Liked On: 05-12-2014, 09:19 PM
I've used that gun and stripper clips :) Well done Ray. Nice work. Would have loved to have been there with mine but just had too much on!.
Liked On: 05-12-2014, 05:54 PM
Headed into town with my hunting gear and a ferret tail that needed to be dropped into H&F for the http://www.huntingandfishing.co.nz/swamp-comp as PT wasn't here to enter the tail. I entered it for...
Liked On: 29-11-2014, 09:28 PM
The silver series detriots 8v53, 8v72 and 8v96 ( fuel pincher) were supercharged and turbocharged Tomoana freezers has two V16 detroits as back up generator engines I used to service them when...
Liked On: 27-11-2014, 10:06 PM