jackson21
Member

251 Likes

Page 3 of 17 First 1234567891011121314151617 Last

• Jump to page:

1. 
   jackson21 liked post by mpf On thread : 300 PRC why hasnt it achieved greater popularity ?

   No ,its because I shot the last elephant in the kawekas years ago

   Liked On: 30-05-2023, 10:25 PM

2. 
   jackson21 liked post by alanpyc On thread : Kroseg stocks (formerly hi tech)

   My Kroseg stock arrived today. That was quick (placed order on 2nd of May, was quoted June / July delivery) Overall quality feels very good, most importantly it is light as at 749g !!:D 225237

   Liked On: 29-05-2023, 01:12 PM

3. 
   jackson21 liked post by chainsaw On thread : What's it worth, rem 700

   Stainless? Or blued ? $900-1000 for rifle if stainless, suppressor depends what it is ? $200-250 ?

   Liked On: 20-05-2023, 10:10 PM

4. 
   jackson21 liked post by norsk On thread : Is this really the state of component shortages?

   I bought a S&B PMI 2 because I had dreamed about one for over 20 years. I would say its not as bright optically as my Kahles or meopta but it tracks around the target perfectly always returning to...

   Liked On: 15-05-2023, 07:15 PM

5. 
   jackson21 liked post by Kiwi Greg On thread : Projectile Length to Ogive

   Even top end custom projectiles vary lot to lot, no surprises mass produced cheap projectiles do Worst I had was 270 Nosler Ballistic tips, 1mm/40 thou longer for given ogive o/a measurement...

   Liked On: 14-05-2023, 11:15 PM

6. 
   jackson21 liked post by mikee On thread : Thermal scopes - best bang for your buck?

   For me the biggest thing is the after sales service / repairs. Its no good having the best gear if when it breaks (its electronic remember) it take months and cost megabucks to repair. Most...

   Liked On: 14-05-2023, 07:47 PM

7. 
   jackson21 liked post by zimmer On thread : Projectile Length to Ogive

   I normally expect variation to occur lot to lot. The projectiles are spewing off a lot of die lines operating side by side all at different states of wear. Also the the lot to lot variations may not...

   Liked On: 14-05-2023, 04:44 PM

8. 
   jackson21 liked post by veitnamcam On thread : Sighting a 223 for longer shots

   2" high at 100 will be close but as mentioned previously actually zero at 200 then you will know it is on.

   Liked On: 05-05-2023, 11:31 AM

9. 
   jackson21 liked post by Pommy On thread : Kroseg stocks (formerly hi tech)

   There's always a possibility that you will need to bed a composite, laminate, walnut, or synthetic stock, in order to get the most out of a rifle. Heck I've even had a chassis that needed some work.

   Liked On: 01-05-2023, 09:12 PM

10. 
    jackson21 liked post by veitnamcam On thread : Kroseg stocks (formerly hi tech)

    I got one for a Howa mini not long after his untimely demise so not sure if it was old stock or manufactured under new management but I was up 4 clicks and perfect.

    Liked On: 01-05-2023, 09:11 PM

11. 
    jackson21 liked post by Dundee On thread : 22 ammo testing for gong shoots

    just use a stirling 14p .22lr and you will never miss!:thumbsup:

    Liked On: 11-04-2023, 11:33 PM

12. 
    jackson21 liked post by Moa Hunter On thread : Tikka bell and carlson stock

    I would look up what B&C say. I put a B&C stock on a mates T3 last year and it transformed it. They still need a skim bed on the Ali bedding block. So relieve the Ali block and wrap tape around the...

    Liked On: 06-04-2023, 10:16 PM

13. 
    jackson21 liked post by XR500 On thread : April Fools get together - Central North Island

    February is almost done and dusted, and as we met quite a few GC's at the first open home here outside of Kinloch, I thought I'd offer up our farm again for a bit of a get together prior to Easter,...

    Liked On: 02-04-2023, 09:33 PM

14. 
    jackson21 liked post by grandpamac On thread : The future of Rifle Ranges.

    Greetings -BW- and small_caliber, Your posts pretty we sum up the problem. Either creating or bringing into compliance an existing range requires a clear eyed understanding of the requirements,...

    Liked On: 31-03-2023, 07:47 PM

15. 
    jackson21 liked post by Friwi On thread : What 22-250 in a 1-8 twist.

    To go Semi factory 1in 8 twist, you have to buy two tikkas. 1 varmint one in 223 1 in 8 twist that you rechamber and use the bolt of a standard 22-250/ 308 bolt face. But then you end up with a...

    Liked On: 31-03-2023, 09:34 AM

Page 3 of 17 First 1234567891011121314151617 Last

• Jump to page: