Jhon
Member

1211 Likes

Page 12 of 81 First 123456789101112131415161718192021222324252662 ... Last

• Jump to page:

1. 
   Jhon liked post by Ingrid 51 On thread : An oldy but a goodie - 6.5x55 Swedish

   259429259430

   Liked On: 18-09-2024, 08:24 PM

2. 
   Jhon liked post by Ingrid 51 On thread : An oldy but a goodie - 6.5x55 Swedish

   I have several Swedes: 1900 Oberndauf, 1916 CG with Elm stock (shooting prize/Sweden 1947), 1941 Husky m38B, CG target rifle with heavy barrel and Soderin aperture sights. Lastly is my Tikka with...

   Liked On: 18-09-2024, 08:23 PM

3. 
   Jhon liked post by Tentman On thread : Rifles from the back of the Cabinet

   Recently there was a Weaver Micro Trac (so not that old, but definitely retro) 20x target style scope on TM and it came my way for pretty modest money. Once it arrived and tested fine I had a good...

   Liked On: 18-09-2024, 08:07 PM

4. 
   Jhon liked post by blip On thread : Poor bugger

   not everyone that hunts with a rifle is an ace hunter either, I now guys that are the best of the best and are top shooters and have all the stories in the world about what ace shots they are but try...

   Liked On: 15-09-2024, 10:58 PM

5. 
   Jhon liked post by 7mmwsm On thread : Demise of the 7mm Rem Mag

   Haha. You 223 guys have whipped the vegans for persistence and are now sounding like the godbothers who turn up on the doorstep and don't take hints that their time would be better spent on someone...

   Liked On: 13-09-2024, 10:49 PM

6. 
   Jhon liked post by Longrun On thread : Lower than expected velocities

   I don't think increasing neck tension increases velocity/pressure much. Consistent neck tension affects ES of load. The load in question has a ES of 30 which is not too bad. I suspect the load...

   Liked On: 06-09-2024, 02:49 PM

7. 
   Jhon liked post by John Duxbury On thread : 243 on deer

   I dont understand the .243 detractors. I have never found the boundaries of it. I can't see where I would shoot a deer with a .308 that would kill it when the .243 wouldn't. However, some factory...

   Liked On: 06-09-2024, 12:49 PM

8. 
   Jhon liked post by Marty Henry On thread : Lower than expected velocities

   Max velocity gets you reduced case life, more throat erosion, burns more powder, recoils a bit more which can help refine a flinch nicely. Accuracy Uber alles for me with as much speed as practical

   Liked On: 06-09-2024, 10:06 AM

9. 
   Jhon liked post by Marty Henry On thread : What sight is this off, anyone?

   Ingenuous windage is on the pivot screw.

   Liked On: 05-09-2024, 05:59 PM

10. 
    Jhon liked post by blip On thread : What sight is this off, anyone?

    It does have that look about it

    Liked On: 05-09-2024, 02:19 PM

11. 
    Jhon liked post by gundoc On thread : What sight is this off, anyone?

    I think it is a home-made tang sight using a modified SMLE rear sight elevation slide.

    Liked On: 05-09-2024, 11:21 AM

12. 
    Jhon liked post by Dicko On thread : What sight is this off, anyone?

    Tang sight of some kind? Sent from my iPhone using Tapatalk

    Liked On: 05-09-2024, 11:11 AM

13. 
    Jhon liked post by Tararua Phil On thread : Identify 7.62x39 Ammo

    The Chinese???? steel(1981) will be corrosive but the German MEN brass(1985) will not. Both will be Berdan primed I'd say.

    Liked On: 05-09-2024, 11:10 AM

14. 
    Jhon liked post by Nasty Factory Trigger On thread : Read if you have Hornady Camlock Bullet Puller

    Have one too - done a fair bit of work - I've found that the handle cam lobes wear or rather distort where it interfaces with said concave bearing surface... flaring the material out - cleaned up...

    Liked On: 04-09-2024, 12:30 PM

15. 
    Jhon liked post by Machurite On thread : Cast Lead Thread ?

    I make my own moulds for 45/70, and im using lead at around 10 to 14BHN depending on the mould also use the pencil check method it works fine, shooting out to 960 yards with open sights

    Liked On: 03-09-2024, 02:58 PM

Page 12 of 81 First 123456789101112131415161718192021222324252662 ... Last

• Jump to page: