Jhon
Member

1211 Likes

Page 80 of 81 First ... 3066676869707172737475767778798081 Last

• Jump to page:

1. 
   Jhon liked post by Husky1600 On thread : 7x57mm 1st effort - comments?

   I use 2206H in my 7x57 with 140's, slightly more than you loads, but not much. And for about the same velocity. Theres something pretty satisfying hitting an animal with a 7x57, they all seem to go...

   Liked On: 12-01-2021, 08:23 PM

2. 
   Jhon liked post by distant stalker On thread : 7x57mm 1st effort - comments?

   38 and 39 gr give you the most consistent speeds (granted less shots so potentially advantaged) if not playing with other powders i would be tempted to adjust seating depths at those charge weights...

   Liked On: 12-01-2021, 08:23 PM

3. 
   Jhon liked post by zimmer On thread : 7x57mm 1st effort - comments?

   Yeah W760 morphed into H414, or maybe the other way around, around the time Hodgdon took over the marketing of Winchester powders. Old old reloading data should show a difference between the 2...

   Liked On: 12-01-2021, 08:22 PM

4. 
   Jhon liked post by BSA On thread : 7x57mm 1st effort - comments?

   Have a BSA Viscount in 7x57. With 140 Sierra pills it grouped best at 44.5 and then at 47.0 of H414 (which is W760 with the Hodgon label)). Seated 30 thou off the lands. Sub moa consistently with...

   Liked On: 12-01-2021, 05:56 PM

5. 
   Jhon liked post by Dicko On thread : 7x57mm 1st effort - comments?

   Jhon, Some general comments on loading for the 7mm Mauser from my experience with ex mil 98 spotters and a rimmed single shot. I support Mathais’ comments on WW760, it seems to be excellent in...

   Liked On: 12-01-2021, 05:55 PM

6. 
   Jhon liked post by Mathias On thread : 7x57mm 1st effort - comments?

   Only comment I can add, I always used W760 powder & a magnum primer for the 7x57 with excellent results. 760 is a very dense ball powder, so the mag primer was a good option for ignition. From memory...

   Liked On: 12-01-2021, 04:06 PM

7. 
   Jhon liked post by Kiwi Sapper On thread : Has our ability to buy loose lead shot ceased?

   Thank you Jhon. Jim160 has PM'd me and solved my problems....Well, apart from the "unacceptable to discuss except in a pubic space" ones. :>)_

   Liked On: 11-01-2021, 10:22 AM

8. 
   Jhon liked post by R93 On thread : Keeping it Simple for New Handloaders

   Just take the whole decapping assembly out and resize as normal. Or if you have case mouths that are out if round, just remove the decapping pin. I use a universal decapping die and never use the...

   Liked On: 09-01-2021, 04:46 PM

9. 
   Jhon liked post by Micky Duck On thread : Reloading brass hulls for an English Black powder s/b/s 12 gauge.

   and MANY modern .12ga arent really .12ga anymore as they are overbored so closer to what was traditionally a .10ga but correct they still fire same shells just have little if any forcing cone so...

   Liked On: 09-01-2021, 09:24 AM

10. 
    Jhon liked post by Micky Duck On thread : Reloading brass hulls for an English Black powder s/b/s 12 gauge.

    look up Wingmans thread on everlasting .410 shells

    Liked On: 09-01-2021, 09:23 AM

11. 
    Jhon liked post by norsk On thread : Reloading brass hulls for an English Black powder s/b/s 12 gauge.

    They will be fine. Brass is a lot stronger than Plastic

    Liked On: 09-01-2021, 07:40 AM

12. 
    Jhon liked post by norsk On thread : Reloading brass hulls for an English Black powder s/b/s 12 gauge.

    Cork floor tiles or even carpet tiles, two wads deep make for a good overpowder wad. Cornflake box or really any "thin-ish" cardboard shiny side out will do for you overshot wad. Make a 11...

    Liked On: 09-01-2021, 04:03 AM

13. 
    Jhon liked post by dannyb On thread : Keeping it Simple for New Handloaders

    You make some valid points, and yeah .1" very likely is variation in shooter rather than load/seating depth variation. Still fun to play with and good to know that seating depth can make a...

    Liked On: 29-12-2020, 02:14 PM

14. 
    Jhon liked post by G.I_Joel On thread : Keeping it Simple for New Handloaders

    As a rookie reloader, I started pistol reloading during lock down and rifle a month after, this forum helped immensely. I was lucky enough to have been given some gear to get me started but also...

    Liked On: 26-12-2020, 08:58 PM

15. 
    Jhon liked post by Tussock On thread : Keeping it Simple for New Handloaders

    Main thing for beginners in my humble opinion is start with premium components. Full length resize. Don't bother with much finicky stuff, just learn to set the projectile up just off the lands...

    Liked On: 26-12-2020, 08:57 PM

Page 80 of 81 First ... 3066676869707172737475767778798081 Last

• Jump to page: