Joe_90
Rocks in his pockets

1427 Likes

Page 54 of 96 First ... 44041424344454647484950515253545556575859606162636465666768 ... Last

• Jump to page:

1. 
   Joe_90 liked post by Barefoot On thread : Size of your hunting knife?

   Wow those keys are sharp :D

   Liked On: 05-09-2021, 10:10 PM

2. 
   Joe_90 liked post by SixtyTen On thread : Howa Mini action - Carbon Stock Project

   Fridge or freezer compressor. One line blows and the other sucks. You can make super quiet low volume air compressors or vacuum pumps from them. Super handy. A vac pump from one of these pulls a...

   Liked On: 05-09-2021, 03:08 PM

3. 
   Joe_90 liked post by Scott Cowan On thread : Lockdown light weight carbon wrap stock build - Here we go

   177631177632 that coat went well, didnt gain much weight. will finish below 600g im confident of that now. Still curing, will sand again tomorrow. sorry its so slow guys lol

   Liked On: 04-09-2021, 10:24 PM

4. 
   Joe_90 liked post by Scott Cowan On thread : Lockdown light weight carbon wrap stock build - Here we go

   177497177499177500 Man I was relieved it popped out clean. time for sanding the nibs off then sanding the whole surface ready for next coat. I may let each coat harden and sand back between coats to...

   Liked On: 04-09-2021, 12:38 AM

5. 
   Joe_90 liked post by Scott Cowan On thread : Lockdown light weight carbon wrap stock build - Here we go

   177416177417177418177419 curing well. bit of lifting and nibs that will need to be sanded off.

   Liked On: 03-09-2021, 10:31 AM

6. 
   Joe_90 liked post by stug On thread : Howa Mini action - Carbon Stock Project

   Just bed the first parrallel section of the barrel, you don’t need to go any further.

   Liked On: 03-09-2021, 10:29 AM

7. 
   Joe_90 liked post by Scott Cowan On thread : Lockdown light weight carbon wrap stock build - Here we go

   177367177368 So it trimmed up ready to coat with epoxy again. id definitely not bed it first when doing another... if I ever do another lol. 177369

   Liked On: 02-09-2021, 11:54 PM

8. 
   Joe_90 liked post by viper On thread : Howa Mini action - Carbon Stock Project

   Ahhh, finally I get to see the stock coming to life, that's a fairly involved project @Joe.......... Might be finished next time we catch up....don't eat all the bloody chocolate biscuits either next...

   Liked On: 02-09-2021, 11:30 PM

9. 
   Joe_90 liked post by Scott Cowan On thread : Lockdown light weight carbon wrap stock build - Here we go

   177291 So I as said.. that didn't go smoothly. due to the forend not sticking I employed some superglue, and also at the odd patch that fibers wouldn't go down in joints. the tutorial used spray...

   Liked On: 02-09-2021, 12:08 PM

10. 
    Joe_90 liked post by Scott Cowan On thread : Lockdown light weight carbon wrap stock build - Here we go

    Na, just decided to go for it... and go for it I did. was a stressful evening to say the least... when my blood pressure returns to civility Ill post some more. its currently curing inside with the...

    Liked On: 02-09-2021, 08:01 AM

11. 
    Joe_90 liked post by Scott Cowan On thread : Lockdown light weight carbon wrap stock build - Here we go

    177275 all set for the wrap... just waiting till the resin gets tacky... nervous... no turning back now... should I have done a test?

    Liked On: 01-09-2021, 10:49 PM

12. 
    Joe_90 liked post by SixtyTen On thread : Howa Mini action - Carbon Stock Project

    A good method for laminating complicated shapes and to keep the carbon weave from getting all messed up is to get some 3m painters plastic, lay that down on a flat table and tape it out so there are...

    Liked On: 01-09-2021, 08:38 PM

13. 
    Joe_90 liked post by stug On thread : Howa Mini action - Carbon Stock Project

    I used Sika boom expanding foam to fill the butt and fore-end. It has no structural value just sound deadening. Run a bit of water around inside the butt or fore-end first then tip/shake it all out....

    Liked On: 01-09-2021, 06:59 PM

14. 
    Joe_90 liked post by Russian 22. On thread : Howa Mini action - Carbon Stock Project

    best thing would be to glue a hip flask in the butt stock, fill to the brim of the spirit of your choosing and enjoy. just need to make sure you finish it all so it doesn't slosh!

    Liked On: 01-09-2021, 05:30 PM

15. 
    Joe_90 liked post by TLB On thread : Clip on night vision

    I have a Sytong and a pard 008. The pard has a rangefinder which is extremely useful. This set up pretty much lives on my .22. I have been using the Sytong for rabbit work on the .223. It is a...

    Liked On: 01-09-2021, 03:27 PM

Page 54 of 96 First ... 44041424344454647484950515253545556575859606162636465666768 ... Last

• Jump to page: