john m
Member

2257 Likes

Page 14 of 151 First 1234567891011121314151617181920212223242526272864114 ... Last

• Jump to page:

1. 
   john m liked post by SL600 On thread : What little pesties did you bowl over today?

   232972 Quality time with Popa.

   Liked On: 09-09-2023, 05:54 PM

2. 
   john m liked post by Shearer On thread : What little pesties did you bowl over today?

   Spent a few days chasing these around. Good fun. 232612

   Liked On: 04-09-2023, 02:49 PM

3. 
   john m liked post by Sidetrack On thread : The Lever Aficionados Thread

   Came across this old unloved compact M8-4x33. Had to spend a hour carefully drilling out the screws to remove the old mounts and apart from a few scratches, its actually a pretty decent scope. Wasn’t...

   Liked On: 01-09-2023, 08:43 PM

4. 
   john m liked post by Ingrid 51 On thread : Change of Address requirements

   I assure you my safes are well secured. The issue is providing photos to prove it, when physical inspection was the ‘go to’. I simply do not trust the security of any electronic communication; in...

   Liked On: 01-09-2023, 08:36 PM

5. 
   john m liked post by Cyclops On thread : Change of Address requirements

   Photographs of how my safes are secured would prove nothing (as did an actual inspection). I have two safes, one used for rifles one for ammunition. Both are securely bolted to a concrete block...

   Liked On: 01-09-2023, 08:33 PM

6. 
   john m liked post by timattalon On thread : Change of Address requirements

   Sooo....now when they leak your address and firearms details to the gangs, they will also provide pictures of what security measyres are in place so the theives can arrive with the right tools for...

   Liked On: 01-09-2023, 08:32 PM

7. 
   john m liked post by Micky Duck On thread : Navigation

   226500

   Liked On: 27-08-2023, 03:43 PM

8. 
   john m liked post by Micky Duck On thread : Old bayonet knife...ID, value, restoration?

   the discs that go on angle grinder that look like polypad/plastic string,will derust that without taking metal off.....please give it a good clean up and have decent look at it before getting all...

   Liked On: 25-08-2023, 07:07 AM

9. 
   john m liked post by grandpamac On thread : Changing a Remmington 700 from .270 to .308

   Greetings, I assume that the .270 is a bolt action so what about one of those neat little Bergara single shots in .308. Even new they are around the cost of a rebarrel plus they break down and go in...

   Liked On: 24-08-2023, 05:38 PM

10. 
    john m liked post by blip On thread : Changing a Remmington 700 from .270 to .308

    Just go 30 06, can always down load it to 308

    Liked On: 24-08-2023, 05:38 PM

11. 
    john m liked post by Swanny On thread : Show us your boat

    231800 Well I guess it's still a boat. Cedar and a bit of native strip plank Canadian canoe. About 16 months to build, fibreglass and finish. Still to see the water yet but hopefully in about a...

    Liked On: 24-08-2023, 02:54 PM

12. 
    john m liked post by ROKTOY On thread : Dinner thread?

    Stuffed and Roasted Ox Heart. One of the few offal's that my lovely wife will knowingly and willingly eat. The young fella found half an Ox heart in the freezer and asked if we could have it for...

    Liked On: 21-08-2023, 02:54 PM

13. 
    john m liked post by grandpamac On thread : FL resized rounds wont chamber

    Greetings again BenTheBuilder, Although frustrating at the time the difficulties you are having will teach you much. So to summarise: 1, Factory ammo chambers. 2, Some of your once fired brass...

    Liked On: 14-08-2023, 09:31 AM

14. 
    john m liked post by 7mmwsm On thread : What little pesties did you bowl over today?

    231026 One less. Don't get many of these. Usually get Stoats.

    Liked On: 13-08-2023, 11:09 AM

15. 
    john m liked post by Mangusta On thread : BRNO 600 Question

    230916

    Liked On: 11-08-2023, 03:45 PM

Page 14 of 151 First 1234567891011121314151617181920212223242526272864114 ... Last

• Jump to page: