Day off today, so its wild pork belly burnt ends, smoked on the bbq for 2 hours at 120 Celsius, then into the cast iron pot for another hour with bbq sauce concoction and butter. 171198
Liked On: 27-06-2021, 06:52 PM
Day off today, so its wild pork belly burnt ends, smoked on the bbq for 2 hours at 120 Celsius, then into the cast iron pot for another hour with bbq sauce concoction and butter. 171198
Liked On: 27-06-2021, 05:22 PM
Day off today, so its wild pork belly burnt ends, smoked on the bbq for 2 hours at 120 Celsius, then into the cast iron pot for another hour with bbq sauce concoction and butter. 171198
Liked On: 27-06-2021, 02:08 PM
Only once with federal brass, 300wsm, 168amax, rl17 cant particularly remember the amount of powder but it wasnt over stoked, not over pressure on the first firings, second firings was popping the...
Liked On: 23-06-2021, 10:51 PM
Rl17 will work well with the 150 gr weight range. Never had any experience with heavier though sorry
Liked On: 22-06-2021, 11:18 AM
2208 will do the job in a 20" bbl perfectly
Liked On: 18-06-2021, 07:30 AM
Can you catch the sharp edge with your fingernail? If so id hazard a guess that your die has some form of manufacturing defect. Pull it apart give it a clean, send a scribe or anything pointy up the...
Liked On: 16-06-2021, 12:38 PM
I run the 120ttsx in 7mm08 bushpig, and to be honest, ill either sell my stock off or shoot them then switch over to a bog standard gameking. ( Just my personal and only experience with ttsx) 20"...
Liked On: 12-06-2021, 12:57 PM
I run the 120ttsx in 7mm08 bushpig, and to be honest, ill either sell my stock off or shoot them then switch over to a bog standard gameking. ( Just my personal and only experience with ttsx) 20"...
Liked On: 12-06-2021, 08:22 AM
I made a rotary wet tumbler as a prototype with random crap i had laying around, drawing up a proper frame now and going to make it out of aluminum at work. Stainless pins are the most expensive part
Liked On: 12-05-2021, 05:21 PM
I made a rotary wet tumbler as a prototype with random crap i had laying around, drawing up a proper frame now and going to make it out of aluminum at work. Stainless pins are the most expensive part
Liked On: 12-05-2021, 04:04 PM
Should be heaps of twist. I shoot both of them through factory tikka 7mm mag barrels. Can't help on the saum front though
Liked On: 05-05-2021, 11:28 AM
Loving my 17" 7mm08, shooting 120gr ttsx at 2970fps, has been veridied on steel out to 685yds( more than what i want to shoot with it) and taken animals out to 210 so far, intended for close up stuff...
Liked On: 28-03-2021, 09:36 PM
Loving my 17" 7mm08, shooting 120gr ttsx at 2970fps, has been veridied on steel out to 685yds( more than what i want to shoot with it) and taken animals out to 210 so far, intended for close up stuff...
Liked On: 28-03-2021, 09:32 PM
Loving my 17" 7mm08, shooting 120gr ttsx at 2970fps, has been veridied on steel out to 685yds( more than what i want to shoot with it) and taken animals out to 210 so far, intended for close up stuff...
Liked On: 28-03-2021, 06:48 PM