m101a1
Member

388 Likes

Page 11 of 26 First 12345678910111213141516171819202122232425 ... Last

• Jump to page:

1. 
   m101a1 liked post by stagstalker On thread : How much camo is too much?

   Does camo help make you harder to identify by eye? Yes. Do you need to it be successful hunting? No.

   Liked On: 06-07-2023, 01:26 PM

2. 
   m101a1 liked post by bumblefoot On thread : Beanie advice

   I've never been a big beanie wearer; but for some reason have always wanted one of these..... 228243

   Liked On: 05-07-2023, 09:04 PM

3. 
   m101a1 liked post by XR500 On thread : "slip on" firefighting or washdown units...

   Ouch!!! Davies water pump twin impellor 2.2K IBC 0.1K Flex hose and fittings 0.25K 20m washdown hose 0.3K Lets call...

   Liked On: 02-07-2023, 07:55 PM

4. 
   m101a1 liked post by STC On thread : NZDA requires FAL number

   Reading through this thread people with the political agenda to end all firearms ownership must rejoice about the amount of petty infighting within the "shooting community" Luckily, wherever I go,...

   Liked On: 28-06-2023, 09:20 PM

5. 
   m101a1 liked post by Micky Duck On thread : homemade ATV Trailer advice

   consider running a heavier beam right up the guts..between your A frame....and if really really clever put slightly smaller box section inside it wit hyour tow hitch attached with a couple of...

   Liked On: 28-06-2023, 09:14 PM

6. 
   m101a1 liked post by Savage1 On thread : homemade ATV Trailer advice

   Get rid of the A-frame and just run a single piece of box section straight back down the middle, it gives you a tighter turning circle which is handy on the farm. You could use the rest of the length...

   Liked On: 28-06-2023, 09:13 PM

7. 
   m101a1 liked post by Cameron92 On thread : NZDA requires FAL number

   Some of the attitudes on here are frankly frustrating for those volunteers, like myself, who put an extraordinary amount of effort into the NZDA branches. I find it almost amusing that the...

   Liked On: 27-06-2023, 06:08 PM

8. 
   m101a1 liked post by Tentman On thread : NZDA requires FAL number

   I just spent the best part of 3 days doing the paperwork associated with keeping our club legal and recertification of the range. Reading these posts makes me doubt the mental capacity of some...

   Liked On: 26-06-2023, 11:33 PM

9. 
   m101a1 liked post by csmiffy On thread : HXP 303 ammo corrosive? found rust in my barrel

   Collins 90 seems to work OK. Was recommended to me. Don't know about its comparison to hoppes but was told hoppes wasn't as good as it used to be. I haven't done enough barrel fouling to see

   Liked On: 24-06-2023, 09:42 PM

10. 
    m101a1 liked post by zeropak On thread : Vacuum packing and liquid

    Ok so here are a few general tips on how to get the job done right and some of the mistakes made which cause the problems mentioned above. Interestingly I have just finished vac packing a little...

    Liked On: 24-06-2023, 09:37 PM

11. 
    m101a1 liked post by Croc On thread : Lee loader kit

    I've got the simple Lee "Challenger Press" and it's awesome. Richard Lee's book - Modern Reloading - says if you're loading 200 a week, go for the multi-station Turret Press. I'm new to the game...

    Liked On: 24-06-2023, 12:07 PM

12. 
    m101a1 liked post by Shearer On thread : Battery chainsaws

    Same. I have an Ozito twin battery at home and use Stihl at work. The Stihl is undoubtably the better saw but then the Ozito was about $200 for the skin. It has done a fair bit of work on firewood...

    Liked On: 23-06-2023, 11:08 PM

13. 
    m101a1 liked post by TLB On thread : Battery chainsaws

    I have used a few. Just for smaller occasional jobs the bigger ozito double battery one is hard to beat. Under $400 with batteries and will cut logs far bigger than it's bar length. Best thing is...

    Liked On: 23-06-2023, 11:08 PM

14. 
    m101a1 liked post by Bol Tackshin On thread : 22lr barrel length with subs

    Update: just had a nosey and this article says about 16" for maximum velocity for .22lr. https://sportingshooter.com.au/ask-uncle-nick/optimum-barrel-length-for-the-22-rimfire/

    Liked On: 21-06-2023, 11:52 AM

15. 
    m101a1 liked post by Micky Duck On thread : Looking for someone trustworthy in Wellington ( yes I know it’s difficult)

    Brian or tahr would just about have to be my first choice

    Liked On: 17-06-2023, 06:06 PM

Page 11 of 26 First 12345678910111213141516171819202122232425 ... Last

• Jump to page: