Magnetite
Member

135 Likes

Page 3 of 9 First 123456789 Last

• Jump to page:

1. 
   will.i.em liked post by Magnetite On thread : GRT users.

   For maximum “modern bolt action pressure” I would use the CIP or SAAMI spec as bolt thrust is related to the taper of the case.

   Liked On: 16-02-2023, 10:53 PM

2. 
   Shearer liked post by Magnetite On thread : GRT users.

   For maximum “modern bolt action pressure” I would use the CIP or SAAMI spec as bolt thrust is related to the taper of the case.

   Liked On: 16-02-2023, 08:27 PM

3. 
   Average-Lad liked post by Magnetite On thread : Hypothesis: Disproven?

   Interesting idea. Another approach would be one meal a day, and then eat when you have to haul something out. Food is also good for when you need body heat. This is all at your own discretion though.

   Liked On: 12-02-2023, 07:28 PM

4. 
   Jhon liked post by Magnetite On thread : This is F**ked

   I hope my surgeon shoots, now I’ll be able to pay my bill with primers.

   Liked On: 24-01-2023, 09:23 AM

5. 
   Puffin liked post by Magnetite On thread : 6.5-284

   I think your mate has some issues you’ll need to sort out first. With some very rough numbers from GRT you should expect about ~2900fps with a 24” barrel, 2213sc, and the 143gr.

   Liked On: 05-01-2023, 01:02 PM

6. 
   Longrun liked post by Magnetite On thread : What are you using for pressure estimation in your handloads.

   Velocity and Gordon’s Reloading Tool (GRT). I use GRT to predict a load at maximum pressure, and note the velocity. Then run a ladder test up to that velocity. Finally I will calibrate GRT with my...

   Liked On: 12-12-2022, 07:27 PM

7. 
   Moa Hunter liked post by Magnetite On thread : What are you using for pressure estimation in your handloads.

   Velocity and Gordon’s Reloading Tool (GRT). I use GRT to predict a load at maximum pressure, and note the velocity. Then run a ladder test up to that velocity. Finally I will calibrate GRT with my...

   Liked On: 12-12-2022, 11:28 AM

8. 
   dannyb liked post by Magnetite On thread : What are you using for pressure estimation in your handloads.

   Velocity and Gordon’s Reloading Tool (GRT). I use GRT to predict a load at maximum pressure, and note the velocity. Then run a ladder test up to that velocity. Finally I will calibrate GRT with my...

   Liked On: 12-12-2022, 10:18 AM

9. 
   Puffin liked post by Magnetite On thread : BC and spin rate

   If it’s properly stabilized, a gyroscopic stability factor (SG) over 1.5 there won’t be much difference....

   Liked On: 29-10-2022, 09:46 PM

10. 
    Moa Hunter liked post by Magnetite On thread : BC and spin rate

    If you mean muzzle velocity, then yes. If you’re talking about bullet speed during flight then SG increases as velocity drops because velocity decays faster than rpm.

    Liked On: 29-10-2022, 09:15 AM

11. 
    Bagheera liked post by Magnetite On thread : Is reloading much cheaper??

    I've got a 6.5x55 which is basically the same as what you've got. Provided I didn't buy too much gear (didn't happen) my break even mark was around 800 rounds. I allowed $4 per round for factory ammo...

    Liked On: 13-09-2022, 11:06 PM

12. 
    Muttonguts liked post by Magnetite On thread : Bore Rust?

    As for why it's uncleaned. I've been cleaning about every 50 rounds. The last clean was about a month ago. There is just too much contradictory information about cleaning out there. The suppressor...

    Liked On: 09-09-2022, 07:50 AM

13. 
    Maca49 liked post by Magnetite On thread : Bore Rust?

    Still seems to. I'll keep using it till it doesn't.

    Liked On: 08-09-2022, 07:30 PM

14. 
    tetawa liked post by Magnetite On thread : Bore Rust?

    Still seems to. I'll keep using it till it doesn't.

    Liked On: 04-09-2022, 08:49 PM

15. 
    dannyb liked post by Magnetite On thread : Bore Rust?

    Still seems to. I'll keep using it till it doesn't.

    Liked On: 04-09-2022, 12:41 PM

Page 3 of 9 First 123456789 Last

• Jump to page: