makka
Member

568 Likes

Page 11 of 38 First 12345678910111213141516171819202122232425 ... Last

• Jump to page:

1. 
   makka liked post by Finnwolf On thread : Buckshot

   Centimetres is for dressmakers!:D

   Liked On: 24-09-2024, 11:37 AM

2. 
   makka liked post by Ned On thread : Venison Nawabi curry

   Thought I'd try a different curry recipe for some venison and this came out a treat. I'd imagine goat would be brilliant with this. I thought it might not go too well but it's gone to the top of my...

   Liked On: 23-09-2024, 11:18 AM

3. 
   makka liked post by -BW- On thread : "Hunter Class" ?

   I wasn’t referencing any particular shoot. The nature of the shoot, targets and distances are organisers prerogative and I have no opinion as to what others want to shoot at. I was opining on the...

   Liked On: 19-09-2024, 01:17 PM

4. 
   makka liked post by Beetroot On thread : "Hunter Class" ?

   Here’s what I’ve learned from all the shooting comps I’ve been too. 1, Someone will complain regardless of how fair you try make the rules 2, People will always get competitive and try and buy...

   Liked On: 19-09-2024, 01:17 PM

5. 
   makka liked post by XR500 On thread : Jetboat hunting missions

   Gidday, That photo is about 8 kms downstream of the upper limit for that river. Last summer there was bugger all water so you would have been doing exceptionally well to get up there. Above that...

   Liked On: 17-09-2024, 06:26 PM

6. 
   makka liked post by 300Shortmag On thread : Jetboat hunting missions

   Anyone that’s keen on doing some overnight Boating hunting trips with a good boat ? I run 3.3 Attack with Yamaha four stroke that’s got plastic as well on the bottom and are always keen to get...

   Liked On: 17-09-2024, 06:23 PM

7. 
   makka liked post by Shearer On thread : Bush rifles

   The best thing to do is get people used to seeing hunters carrying rifles (where they are allowed to). Make it normal and not something to get all anxious about.

   Liked On: 16-09-2024, 09:50 PM

8. 
   makka liked post by csmiffy On thread : Remington modle 7 CDL 308 twist rate?

   Try the tight patch on a nice spinny cleaning rod and count the twists method

   Liked On: 14-09-2024, 09:12 AM

9. 
   makka liked post by Puffin On thread : 280AI Revisited - Forbes - Load Development

   Just an observation (in case the original photo led folk to think otherwise) is that alignment should be confirmed at two positions, and not with a single placement. The diagram at the side shows how...

   Liked On: 10-09-2024, 09:18 PM

10. 
    makka liked post by akaroa1 On thread : Making everlasting 44 Rinfire reloadable brass

    The key to being able to make these cases is being able to accurately and securely hold them in a lathe And drilling out and tapping the center fire primer hole Screwing in a brass bolt dipped...

    Liked On: 09-09-2024, 11:40 PM

11. 
    makka liked post by gonetropo On thread : 7 Seater for the misso - Vangaurd / X Trail

    its not just a maintenance issue with nissan cvt, they are total crap to start with.

    Liked On: 09-09-2024, 10:05 PM

12. 
    makka liked post by Fee Knicks On thread : Bahco Knives

    It would be a labour of love to re-handle a ten dollar knife. I prefer to accept them as they are and just use them.

    Liked On: 09-09-2024, 03:27 PM

13. 
    makka liked post by Hunter_Nick On thread : Walnut stock build (done the traditional way)

    I’ve contemplated one better than that. I’ve thought about tutoring anyone that wanted to learn, it would just need to right people, right place and enough time. It’s a very slow process, and not...

    Liked On: 09-09-2024, 12:41 PM

14. 
    makka liked post by XR500 On thread : Bahco Knives

    My metal detector pin pointer says the tang finishes 30-35mm before the end of the handle.

    Liked On: 08-09-2024, 09:11 PM

15. 
    makka liked post by 7mmwsm On thread : A question for the doubters

    Just popped up in those short clips that lead on to the next one. Some weird shit appears at times.

    Liked On: 08-09-2024, 02:59 PM

Page 11 of 38 First 12345678910111213141516171819202122232425 ... Last

• Jump to page: