makka
Member

486 Likes

Page 22 of 33 First ... 89101112131415161718192021222324252627282930313233 Last

• Jump to page:

1. 
   rupert liked post by makka On thread : 5.6x57 single shot project

   Whilst I was waiting for a .224 barrel to appear I started work on the extractor as I knew it would be a bit of work to make an extractor for a rimless cartridge. I began by drilling a 12mm hole in...

   Liked On: 27-05-2024, 03:29 PM

2. 
   Dan88 liked post by makka On thread : 5.6x57 single shot project

   Whilst I was waiting for a .224 barrel to appear I started work on the extractor as I knew it would be a bit of work to make an extractor for a rimless cartridge. I began by drilling a 12mm hole in...

   Liked On: 26-05-2024, 11:28 PM

3. 
   Dan88 liked post by makka On thread : 5.6x57 single shot project

   I have been tinkering around with this one for a while so thought I had better do a build thread on it. I picked up a cheap 12ga Baikal after seeing the 30-30 that akaroa1 had built. 251143 ...

   Liked On: 26-05-2024, 11:27 PM

4. 
   Tentman liked post by makka On thread : 5.6x57 single shot project

   Whilst I was waiting for a .224 barrel to appear I started work on the extractor as I knew it would be a bit of work to make an extractor for a rimless cartridge. I began by drilling a 12mm hole in...

   Liked On: 26-05-2024, 11:11 PM

5. 
   Tentman liked post by makka On thread : 5.6x57 single shot project

   I have been tinkering around with this one for a while so thought I had better do a build thread on it. I picked up a cheap 12ga Baikal after seeing the 30-30 that akaroa1 had built. 251143 ...

   Liked On: 26-05-2024, 11:11 PM

6. 
   DUCKHUNTER liked post by makka On thread : Ruger Red Label shotguns?

   I ran an older fixed choke 20ga one for a few years, I found it great and never had an issue of any type

   Liked On: 24-05-2024, 02:38 PM

7. 
   No.3 liked post by makka On thread : Mechanics

   The problem is that they are a stationary holding brake, so applying them on the brake rollers doesnt even simulate how they would be used in real life. I have seen trucks roll away with the cardan...

   Liked On: 23-05-2024, 03:28 PM

8. 
   Finnwolf liked post by makka On thread : Mechanics

   The problem is that they are a stationary holding brake, so applying them on the brake rollers doesnt even simulate how they would be used in real life. I have seen trucks roll away with the cardan...

   Liked On: 23-05-2024, 03:13 PM

9. 
   Micky Duck liked post by makka On thread : Importing brass from Australia????

   I think the 100pc brass, dies and reamer cost $50 to ship. Because it arrived at my folks 2 days after I flew back here:angry:

   Liked On: 18-05-2024, 08:32 PM

10. 
    sore head stoat liked post by makka On thread : Surfcasting : Braid vs Mono

    Braid on my surf casting threadlines (with a mono shockleader), Mono on my surf casting overheads (with braid backing)

    Liked On: 15-05-2024, 10:49 AM

11. 
    kristopher liked post by makka On thread : Another Vintage project and what happens when .....

    Mix glow powder with clear epoxy or nail polish. If you want some, I have plenty and can send you some.

    Liked On: 14-05-2024, 02:00 PM

12. 
    Micky Duck liked post by makka On thread : Another Vintage project and what happens when .....

    Mix glow powder with clear epoxy or nail polish. If you want some, I have plenty and can send you some.

    Liked On: 14-05-2024, 12:26 PM

13. 
    Tommy liked post by makka On thread : Mechanics

    Before I did anything, I'd take it for a drive and give the brakes a proper hiding, then take it straight in for the recheck

    Liked On: 12-05-2024, 10:34 AM

14. 
    tetawa liked post by makka On thread : Mechanics

    Before I did anything, I'd take it for a drive and give the brakes a proper hiding, then take it straight in for the recheck

    Liked On: 12-05-2024, 09:27 AM

15. 
    7mm Rem Mag liked post by makka On thread : What Have You Loaded Today

    55gr Zmax, same as a Vmax just a different colour tip

    Liked On: 08-05-2024, 02:33 PM

Page 22 of 33 First ... 89101112131415161718192021222324252627282930313233 Last

• Jump to page: