makka
Member

486 Likes

Page 29 of 33 First ... 15161718192021222324252627282930313233 Last

• Jump to page:

1. 
   Micky Duck liked post by makka On thread : Rem 700 LA value

   I have an old 338 lapua barrel with enough length to cut and rechamber, so I'm half way there

   Liked On: 15-07-2023, 07:08 PM

2. 
   Micky Duck liked post by makka On thread : Rem 700 LA value

   338-06 is the plan. Micky Duck, I didn't realise you could get them new without a barrel until I looked just now, that could be a good idea unless something else doesn't pop up cheap

   Liked On: 15-07-2023, 05:01 PM

3. 
   Moa Hunter liked post by makka On thread : DIY bullet tips for flat nosed cast bullets

   228560 Somehow managed to bugger up the measurements, and did a shit job of supporting them so now I know what I need to fix for next batch!

   Liked On: 15-07-2023, 01:28 PM

4. 
   Micky Duck liked post by makka On thread : 280 with 168 Bergers

   Will have to keep my eyes peeled

   Liked On: 14-07-2023, 09:51 PM

5. 
   Micky Duck liked post by makka On thread : DIY bullet tips for flat nosed cast bullets

   228560 Somehow managed to bugger up the measurements, and did a shit job of supporting them so now I know what I need to fix for next batch!

   Liked On: 14-07-2023, 04:12 PM

6. 
   T.FOYE liked post by makka On thread : DIY bullet tips for flat nosed cast bullets

   I'm firing up the printer to do some softbait molds, will do a few test BT's for you at the same time

   Liked On: 14-07-2023, 12:48 PM

7. 
   dannyb liked post by makka On thread : Useing the firearms register

   I haven't been around here long, but I know for sure one thing that this register will achieve, dannyb might actually hold onto a gun for a while now!

   Liked On: 26-06-2023, 09:27 PM

8. 
   T.FOYE liked post by makka On thread : DIY bullet tips for flat nosed cast bullets

   I was thinking about 3d printing some the other day, using a resin printer so failing under high temp shouldn't be an issue

   Liked On: 17-06-2023, 10:19 PM

9. 
   Micky Duck liked post by makka On thread : 243 vs .308

   Exactly what I did, was expecting to buy a 308 but ended up with a 270

   Liked On: 17-06-2023, 09:57 AM

10. 
    akaroa1 liked post by makka On thread : Wildcat appreciation thread

    With the amount of 6.5mm projectiles available these days, a 303-6.5 could be a nice rimmed cartridge

    Liked On: 16-06-2023, 04:08 PM

11. 
    Moa Hunter liked post by makka On thread : Call that a dog? Are there any...?

    Our neighbor had a Norwiegan Elk Hound, so they are here. It seemed like a nice enough dog, it let you know if something wasnt right. It kind of reminded me of a Husky x Shephard but with a...

    Liked On: 14-05-2023, 12:32 AM

12. 
    Pete_D liked post by makka On thread : Getting a Farm bike road registered ???

    Revin is pretty straightforward, you just need proof of ownership and proof of previous rego which the vin number should cover. Not all VTNZ/VINZ/AA sites will do bike revin's so you just need to...

    Liked On: 01-05-2023, 10:31 PM

13. 
    Micky Duck liked post by makka On thread : Getting a Farm bike road registered ???

    Im not claiming to know it all but I do know a bit about this kind of thing, so here it goes: -Farm bikes are exempt from the ABS/Combined brake requirements -If it has a VIN plate/ADR plate or...

    Liked On: 01-05-2023, 08:13 PM

14. 
    viper liked post by makka On thread : Legal length.

    I could do something like that, I'm still perfecting getting the printed threads spot on but am pretty close. If I just printed the end cap quite thin then if "it" was to happen then it wouldn't be...

    Liked On: 29-04-2023, 07:18 AM

15. 
    viper liked post by makka On thread : Legal length.

    I have been using fusion 360, been a bit of a learning curve but good fun. I did some thread caps the other day too! 216491 216492

    Liked On: 29-04-2023, 07:15 AM

Page 29 of 33 First ... 15161718192021222324252627282930313233 Last

• Jump to page: